PRONAR T740 Скачать руководство пользователя страница 59

Страница: 59 / 136

3.21

causes tilting of the expander lever, which parts the jaws of the brake shoes immobilising the

trans-shipment trailer.

3.10

TURNING INTERLOCK HYDRAULIC SYSTEM

Trans-shipment trailer as standard equipment in passively steered turning rear axle. Axle

design enables easier cornering and easier manoeuvring on marshy terrain, due to which

there is less tyre wear on machine. While reversing, axle hub must be blocked, otherwise the

trans-shipment trailer will have a tendency to turn uncontrollably to the left or the right during

reversing.

FIGURE 3.16

Rear axle hydraulic interlock system

(1) turning interlock cylinder, (2) rear turning axle, (3) hydraulic quick couplers, (4) hydraulic

conduit, (5) information sticker

Axle interlock is enabled by single conduit hydraulic system shown on figure (

3.16)

. Before

moving to the rear extend hydraulic turning interlock cylinder (1) with the aid of tractor

manifold lever.

Содержание T740









































































































































Результаты поиска

Содержание T740

Отзывы:

Похожие инструкции для T740

Бренды по названию

Популярные бренды

PRONAR T740, Руководство пользователя

Результаты поиска

Содержание T740

Отзывы:

Похожие инструкции для T740

Бренды по названию

Популярные бренды