PRONAR T740 Скачать руководство пользователя страница 41

Страница: 41 / 136

3.3

CONTENTS UNIT

T740

Maximum PTO speed

Minimal clutch working pressure

Maximum clutch working pressure

revs

-1

bar

1 000

3.2

CHASSIS

Trans-shipment trailer chassis is shown on figure (

3.1)

. The frame (1) is made as a welded

structure from steel profiles. The main support elements are two longitudinal rails connected

with crossbars. To the frame is welded the drawbar longitudinal rails, at the end of which is

the hitching eye plate and drawbar eye (5). On the left side of the drawbar is screwed the

support with two gear mechanism.

At the rear part of the frame the suspension is secured (2) tandem type with parabola leaf

springs. The rear axle (4) is made as a turning axle with a hydraulic interlock system for

trailer reversing.

Depending on installed electrical system accessories, weight simulators (10) or loading link

cells are secured in 6 sockets in the upper part of the frame. On them is placed the trans-

shipment trailer load box.

Содержание T740









































































































































Результаты поиска

Содержание T740

Отзывы:

Бренды по названию

Популярные бренды

PRONAR T740, Руководство пользователя

Результаты поиска

Содержание T740

Отзывы:

Бренды по названию

Популярные бренды