PRONAR T740 Скачать руководство пользователя страница 103

Страница: 103 / 136

5.15

ATTENTION!

The trans-shipment trailer and tractor must not be attached if the hydraulic oil in the two

machines is of different types.
Do not use the trans-shipment trailer with damaged hydraulic system.

Tightness inspection:

•

After a week of use

•

Every 12 months of use,

5.2.11 OPERATION NO. 11 - INSPECTION OF LIGHTING AND SIGNALLING

SYSTEM.

Required service actions

•

Hitch trans-shipment trailer to tractor.

•

Switch on all lights in succession.

•

Check completeness and technical condition of lights.

•

Check completeness of all reflective lights.

•

Check correct mounting of triangular slow-moving vehicle sign.

•

Check connection conduit and conduit plug.

•

Check condition of conduit group and connection blocks.

ATTENTION!

Travel with unreliable lighting and signalling system is forbidden. Damaged lamp lenses,

and burned-out bulbs must be replaced before travelling.

Electrical system inspection:

•

daily.

•

Every 12 months of use,

Содержание T740









































































































































Результаты поиска

Содержание T740

Отзывы:

PRONAR T740, Руководство пользователя, Страница: 103 / 136

Результаты поиска

Содержание T740

Отзывы: