PRONAR T740 Скачать руководство пользователя страница 54

Страница: 54 / 136

3.16

FIGURE

3.11

Two conduit pneumatic system diagram with three position

regulator

(1) air tank, (2) control valve, (3) brake force regulator, (4) pneumatic ram, (5), (6) lead

connectors, (7) air filter, (8) air tank control connectors (9) drain valve

Working brake is activated from the tractor driver's cab by pressing on the brake pedal in the

tractor. The function of the control valve (2), applied in pneumatic systems - figure (3.7), is

the operation of the trans-shipment trailer brakes simultaneously when tractor's brakes are

applied Furthermore, in case of an inadvertent disconnection of the conduit between the

trailer and the tractor, the control valve will automatically activate trailer's brakes. Valve used

in the system is equipped with a brake to be applied when trailer is disconnected from the

tractor. When compressed air conduit is connected to a tractor, the device automatically

applying the brakes now changes its position to allow normal brake operation.

Содержание T740









































































































































Результаты поиска

Содержание T740

Отзывы:

PRONAR T740, Руководство пользователя, Страница: 54 / 136

Результаты поиска

Содержание T740

Отзывы: