PRONAR T740 Скачать руководство пользователя страница 118

Страница: 118 / 136

5.30

•

If there is an excessive looseness, loosen tensioner bolt (6) and tighten chain

(1) while lifting the wheel. Tensioner block, joined with tensioner toothed cog (5)

is moved upwards.

•

After achieving required tightness, tighten tensioner bolt (6).

•

If there is still an excessive looseness in the transmission, loosen 4 nuts (4) and

tighten chain (1) using adjustment bolt (3) – connector housing (2) is moved

upwards.

•

After achieving required tightness, tighten nut (4).

5.2.18 OPERATION NO.18 – INSPECTION OF TIGHTNESS OF REAR CHAIN

TRANSMISSION

FIGURE 5.15

REAR CHAIN TRANSMISSION

(1) chain, (2) tensioner toothed cog, (3) tensioner bolt, (4) counter nut, (5) tightening nut

Required service actions

•

Immobilise tractor and trailer with parking brake.

Содержание T740









































































































































Результаты поиска

Содержание T740

Отзывы:

Бренды по названию

Популярные бренды

PRONAR T740, Руководство пользователя

Результаты поиска

Содержание T740

Отзывы:

Бренды по названию

Популярные бренды