probst SH-1000-MINI Скачать руководство пользователя страница 9

Страница: 9 / 56

Operating Instructions

Safety

8 / 34

Safety

3.1

Safety Symbols

Danger to life!

Identifies imminent hazard. If you do not avoid the hazard, death or severe injury will result.

Hazardous situation!

Identifies a potentially hazardous situation. If you do not avoid the situation, injury or damage
to property can result.

Prohibition!

Identifies imminent a prohibition. If you do not avoid the prohibition, death and severe injury,
or damage to property will result.

Important informations or useful tips for use.

3.2

Safety Marking

WARNING SIGN

Symbol

Meaning

Order-No.:

It is not allowed to be under hanging loads.

Danger to life!

2904.0210
2904.0209
2904.0204

30 mm
50 mm
80 mm

The sucked load must never be lifted and transported without
additional securing by the load-securing-chain.

2904.0765

100 x70 mm

The sucked load must never be lifted and transported without
additional securing by the load-securing-chain.

2904.0767

55 x 25 mm

The load-securing-chains must fit tightly to the load.

Prohibition:

load-securing chains must never hang loose under the

load!

2904.0689

70x41 mm

Содержание SH-1000-MINI

























































Результаты поиска

Содержание SH-1000-MINI

Отзывы:

Похожие инструкции для SH-1000-MINI

Бренды по названию

Популярные бренды

probst SH-1000-MINI, Руководство по эксплуатации

Результаты поиска

Содержание SH-1000-MINI

Отзывы:

Похожие инструкции для SH-1000-MINI

Бренды по названию

Популярные бренды