probst SH-1000-MINI Скачать руководство пользователя страница 17

Страница: 17 / 56

Operating Instructions

Installation

16 / 34

Installation

4.1

Mechanical connection

Use only original accessories, in case of doubt consult the manufacturer.

Take care that the

carrying capacity / working load

limit (WLL) of the lifting device/carrier is

not exceeded

through the load of the device, the attaching devices (turning device, fork sleeves etc.) and the additional
load of the gripping goods!

Gripping devices

always

have to be

gimballed

, so they can swing freely in any position.

no case

it is allowed to mount gripping devices with lifting devices/carriers in a

rigid way

Break of the suspension may occur within short time. Death, severe injuries and material damage can
result

4.1.1

Lifting eye / Suspension bolt

•

The device is equipped with a lifting eye / suspension bolt and can be mounted on various carrier /
lifting devices.

•

Take care that the lifting eye / suspension bolt is safely joined with the lifting tackle (e.g. crane hook,
belt) and cannot slide down.

4.1.2

Load hooks and slings

The device is attached to the carrier/lifting device with a load hook or a suitable sling.

Ensure that the single chains strands are not twisted or knotted.

Attaching the device to the lifting device/carrier, take care that all local safety regulation is observed.

Содержание SH-1000-MINI

























































Результаты поиска

Содержание SH-1000-MINI

Отзывы:

Похожие инструкции для SH-1000-MINI

Бренды по названию

Популярные бренды

probst SH-1000-MINI, Руководство по эксплуатации

Результаты поиска

Содержание SH-1000-MINI

Отзывы:

Похожие инструкции для SH-1000-MINI

Бренды по названию

Популярные бренды