probst SH-1000-MINI Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 56

background image

Operating Instructions

Safety

11 / 34

V4

GB

3.3

Function Control

•

Before using the device check the functions and the working condition.

•

Maintenance and lubrication are only permitted when device is shut down!

•

Do not use the device, until all faults which can cause safety hazards are removed.

•

If there are any cracks, splits or damaged parts on any parts of the device, immediately stop using it.

•

The operating instructions must be available at the workplace every time.

•

Do not remove the data-plates of the machine.

•

Unrecognisable information signs must be replaced.

3.3.1

Safety at work

•

The use of the vacuum lifting device is only permitted in proximity to the ground.

In hoist operation

:

The suctioned load must be lowered immediately after picking up (e.g. from a pallet or a truck) to just

above the ground

(approx. 20 - 30 cm).

The load must then be secured by the

load securing chain

and may only then be transported to the

installation site. To transport the load, lift it only as high as necessary (recommended approx. 0.5 m
above the ground).

It is forbidden to swivel the device over persons.

Danger to life!

•

The manual guiding of is only allowed for devices with handles.

•

The operator is not allowed to leave the control unit as long as the vacuum lifting device loaded with
load (stone slab). The load must always be in the range of vision of the operator.

•

Always keep an eye on the vacuum gauge. Never lift loads when the vacuum is below the required under
pressure (mbar). If the pointer of the pressure gauge moves into the red danger zone,

lower the load

immediately!

Danger! Load could fall down!

•

While using the vacuum lifting device is the stay of persons in the working area forbidden. Except it is
indispensable. Caused of the way of using the vacuum lifting device , e.g. if the device must be leaded by
hand.

•

While using the vacuum lifting device be sure that there are no persons in the working area.

Danger to

Life!!

•

The device must never be subjected to a force acting in a lateral direction due to diagonal pulling.

•

Do not lift any components off-centre, because that could fall down.

Danger of tilting!

•

Release the load only when it is completely safely resting on the surface.

Keep fingers away from the

load when you release it as they can be crushed!

•

The capacity and the nominal width the vacuum lifting device are not allowed to cross over.

•

Do not use the vacuum lifting device to jerk seized set down load.

•

Jerking up or down

of the unit with or without load is

prohibited

! Unnecessary vibrations must be

avoided. As well as

fast driving

with the carrier/ hoist over uneven terrain! Danger to life/accident: The

load could fall or the load handling attachment could be damaged! As a general rule,

only

drive at

walking speed

with the lifted load!

«
...
10
11
12
13
14
...
»

Содержание SH-1000-MINI

























































Отзывы:

Нет отзывов

Похожие инструкции для SH-1000-MINI

Бренд: TCS Страницы: 16

Бренд: Cerdi Страницы: 24

Бренд: PrimeWeld Страницы: 23

Бренд: HÜRNER Страницы: 33

Бренд: National Instruments Страницы: 13

Бренд: Balluff Страницы: 124

Бренд: Bishamon Страницы: 19

Бренд: Powrmatic Страницы: 36

Бренд: Parweld Страницы: 15

Бренд: Kamatec Страницы: 28

Yeast Harvester

Бренд: Blichmann Страницы: 4

Бренд: Yeswelder Страницы: 56

Бренд: Robertshaw Страницы: 35

Бренд: HEIDENHAIN Страницы: 362

Бренд: HEIDENHAIN Страницы: 581

Бренд: Blue Giant Страницы: 24

Бренд: Parkside Страницы: 113

Tradestig AC 220

Бренд: Murex Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды