probst SH-1000-MINI Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 56

background image

Operating Instructions

Safety

14 / 34

V4

GB

3.10

Inspecting the vacuum hoses and hose clamps

•

Check that all vacuum hoses and hose clamps are securely seated. Tighten any loose
connections.

3.10.1

Testing the vacuum reservoir

•

See the sub-

section "Leak test" in the section ”Maintenance”

•

Rectify any detected faults before using the lifting device. If a fault becomes apparent during,
switch off the lifting device and rectify the fault.

3.11

Damages of suction plate

Avoidance of damages:

•

To avoid damages of the rubber seal on the suction plate (chinks, abrasion) take notice, that:

•

during the operation (lifting, transporting and lowering) with the device, the suction plate does not brush or
pump against other products or materials.

•

Otherwise the rubber seal on the suction plate could be damaged (danger of pressure loss).
Load could fall down.

Danger of accidents!

3.12

Protective equipment

The protective equipment must consist, according to the safety regulations
of the following parts:

•

Protective clothing

•

Safety gloves

•

Safety shoes

•

Hearing protector

«
...
13
14
15
16
17
...
»

Содержание SH-1000-MINI

























































Отзывы:

Нет отзывов

Похожие инструкции для SH-1000-MINI

Бренд: National Instruments Страницы: 20

Бренд: National Instruments Страницы: 6

Бренд: National Instruments Страницы: 30

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 37

Бренд: National Instruments Страницы: 8

Бренд: Handicare Страницы: 20

Бренд: Jefferson Страницы: 24

Бренд: Absima Страницы: 5

Бренд: M-system Страницы: 10

AUTOPULSE IQ-318

Бренд: Notifier Страницы: 62

Бренд: Neilsen Страницы: 9

Бренд: Holzmann Страницы: 23

Бренд: Raider Страницы: 74

Бренд: P.I.T. Страницы: 34

Бренд: Unimig Страницы: 14

Бренд: ICP DAS USA Страницы: 2

ThermoPro G4 Series

Бренд: Curtis Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды