background image

(at rough conditions shorten the 
interval) 

33 / 34 

 

 
 

5240.0020 

V4 

GB 

 
 

7.8

 

Leak test 

 

Switch on the lifting device/engine. 

 

Place the lifting device on a piece of sheet metal or a similar surface and apply suction. 

Caution: 

Only apply suction to the sheet; do not lift it! It can loosen while being checked and fall off. 

 

Switch the pump on and wait until a vacuum pressure of -0.6 bar is reached. 

 

Switch off the engine and watch the pressure gauge. Suction should not decrease by more than 0.1 bar within 5 
minutes. If it does, locate the cause for this error and correct it before operating the device. 

 

7.9

 

Safety procedures 

 

 

It is the contractor’s responsibility to ensure that the device is checked by an expert in periods of 

max. 1 year and all recognized errors are removed (

 see DGUV regulation 1-54 and DGUV norm 100-500). 

 

The corresponding legal regulations and the regulations of the declaration of conformity must be 
observed! 

 

The expert inspection can also be done by the manufacturer Probst GmbH.  
Contact us at: 

service@probst-handling.de

 

 

We recommend affixing 

the inspection sticker "„Sachkundigenprüfung / Expert inspection" in a clearly 

visible place (order no.: 2904.0056+Tüv sticker with year number) after the inspection has been done. 

 

 

 

The check by an expert must be proved! 

 

Device 

Year 

Date 

Expert 

Company 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание SH-1000-MINI

























































Отзывы: