probst SH-1000-MINI Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 56

probst SH-1000-MINI Скачать руководство пользователя страница 4

Operating Instructions

EC-Declaration of Conformity

3 / 34

V4

GB

6

Troubleshooting .................................................................................................................................................. 28

7

Maintenance and care ......................................................................................................................................... 29

7.1

Maintenance ............................................................................................................................................................ 29

7.1.1

Electrics .................................................................................................................................................................... 29

7.2

Maintenance plan .................................................................................................................................................... 30

7.3

Vacuum pump (TFK 12) ............................................................................................................................................. 31

7.4

V-Belt ......................................................................................................................................................................... 31

7.5

Suction pads/ seals ...................................................................................................................................................32

7.6

Vacuum filter .............................................................................................................................................................32

7.7

Warning device (audible) .........................................................................................................................................32

7.8

Leak test ................................................................................................................................................................... 33

7.9

Safety procedures ................................................................................................................................................... 33

7.10

Hints to the type plate ............................................................................................................................................. 34

7.11

Hints to the renting/leasing of PROBST devices .................................................................................................... 34

«
...
2
3
4
5
6
...
»

Содержание SH-1000-MINI

























































Отзывы:

Нет отзывов