ProActiv SPEEDY 4all Скачать руководство пользователя

Страница: 63 / 92

Usage instructions SPEEDY 4all & 4you & 4teen

25.4 Knee lever brake with lock

Figure 175: Knee lever brake with lock

To release or apply the knee lever brake, pull
the locking knob out of its lock and turn it 90°.
The brake lever can then be used to apply or
release the brake.

Figure 176: Locking knob pulled out of lock and
turned 90°

The

brake is closed

by pushing the brake

lever forwards and downwards. In the closed
position, the brake pin pushes the tyre in by
approx. 4 mm (at the specified air pressure in
the tyre).

Figure 177: Brake opened, closed by pushing the
brake lever forwards and downwards

Please note that the knee lever brake is a

parking brake which may only be applied when
the product is at a standstill. This is not a ser-
vice brake which is suitable for reducing
speed.

open the brake

, pull the brake lever back

up and rearwards again. In the open position,
the distance between the brake pin and the
tyre is approx. 3 to maximum of 4 mm.

Figure 178: Brake closed; opening done by pulling
the brake lever up and rearwards

lock

the brake position, turn the locking

knob 90° and allow it to engage in the intended
hole in the locking block.

Locking knob

Close brake

Brake lever

Open brake

Locking knob not
locked

Содержание SPEEDY 4all





























































































Результаты поиска

Содержание SPEEDY 4all

Отзывы:

Похожие инструкции для SPEEDY 4all

Бренды по названию

Популярные бренды

ProActiv SPEEDY 4all, Инструкции по использованию

Результаты поиска

Содержание SPEEDY 4all

Отзывы:

Похожие инструкции для SPEEDY 4all

Бренды по названию

Популярные бренды