ProActiv SPEEDY 4all Скачать руководство пользователя страница 57

Страница: 57 / 92

Usage instructions SPEEDY 4all & 4you & 4teen

Figure 156: M5 joint screws for setting the actuating
force of the brake lever

Note:

The brake pin is usually mounted in the stand-
ard position (see following figure). The assem-
bly of the brake pin in the other possible posi-
tion (see following figure) may be necessary
after the adjustment of the drive wheels.

Figure 157: Positions of the brake pin

25.1.3 Brake adjustment on the SPEEDY

4all Ergo and SPEEDY 4you Ergo
models

The following instructions are intended

for and may only be carried out by a rehabilita-
tion specialist dealer or PRO ACTIV

Settings on the brake could be necessary for
the following reasons:



You have changed the tyre or the tyre

pressure.



You have changed the wheel tracking or

the position of the drive wheels.



The brake is pulling unevenly or insuffi-

ciently after extended use.

To adjust the knee lever brake, proceed as
follows on both sides:

1. Initial situation: Drive wheels mounted on

the product and the knee lever brakes
open. The drive wheels have the specified
inflation pressure.

2. For the

correct positioning

of the knee

lever brake, slightly loosen the M5 clamp
screws (AF 4 mm) so that the knee lever
brake can be moved on the hexagon rail.

Figure 158: M5 clamp screws on the hexagon rail
(view from the inner side of the product)

3. Position the opened brake on the hexagon

rail so that there is a distance of approx. 3
to max. 4 mm between the brake pin and
the tyre.

M5 joint screws

Standard position
of the brake pin

M5 clamp screws

Hexagon
rail

Other possible
position

Содержание SPEEDY 4all





























































































Результаты поиска

Содержание SPEEDY 4all

Отзывы:

Бренды по названию

Популярные бренды

ProActiv SPEEDY 4all, Инструкции по использованию

Результаты поиска

Содержание SPEEDY 4all

Отзывы:

Бренды по названию

Популярные бренды