Poweramp LHP Series Скачать руководство пользователя страница 36

Страница: 36 / 52

4111-0012 — Sept. 2018

• Check fuse(s) and circuit breaker(s). Replace any

blown fuse(s) with a fuse of equal specification.

• Make sure the correct voltages are present at the

proper locations inside the control panel(s).

Before performing the detailed troubleshooting procedures, check the following items first:

Symptom

Possible Cause

Solution

Platform does not rise.

Motor does not energize.

Motor overload device

tripped.

Reset overload relay or breaker. Determine cause of

device tripping.

Motor starter (three-

phase) or motor relay

(single-phase) not

energizing.

Check voltage at starter or relay coil.

• If voltage is present and starter or relay does not

energize, replace starter or relay.

• If voltage is not present, check all components in

series with the starter or relay coil.

Three-phase units only:

Platform does not rise.

Motor runs in reverse

Phase reversed.

Reverse any two legs at the branch circuit

disconnect.

When service under the dock leveler is required,

always lock all electrical disconnects in the OFF

position after raising the platform and engaging the

maintenance prop.

Always post safety warnings and barricade the

work area at dock level and ground level to prevent

unauthorized use of the dock leveler before

maintenance is complete.

A hard hat or other applicable head protection

should always be worn when working under or

around a dock leveler.

Always stand clear of platform lip when working in

front of the dock leveler.

Unless the dock leveler is equipped with a tethered

remote, two people are required to engage the

maintenance prop: one person to operate the unit,

the other person to engage the maintenance prop.

In addition, it is recommended and good safety

practice to use an additional means to support

the dock platform and lip anytime when physically

working in front of or under the dock leveler. This

additional means may include, but is not limited to a

boom truck, fork truck, stabilizing bar or equivalent.

TROUBLESHOOTING

Содержание LHP Series





















































Результаты поиска

Содержание LHP Series

Отзывы:

Похожие инструкции для LHP Series

Бренды по названию

Популярные бренды

Poweramp LHP Series, Инструкция для владельца и пользователя

Результаты поиска

Содержание LHP Series

Отзывы:

Похожие инструкции для LHP Series

Бренды по названию

Популярные бренды