Poweramp LHP Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 52

background image

30

4111-0012 — Sept. 2018

© 2018 Systems, LLC

A— Lip Area

B— Platform Hinge Area

C— Main Cylinder Pins

D— Lip Cylinder Pins

Periodic Maintenance

Figure 23

MAINTENANCE

To ensure normal operation of the dock leveler, use

only aircraft hydraulic fluid designed to meet or exceed

military specification MIL-H-5606-G. It is recommended

that the following hydraulic fluids be used:

• ULTRA-VIS-HVI-15

• Aero Shell Fluid 4 or Fluid 41

• Mobil Aero HFA Mil-H5606A or Aero HF

• Texaco Aircraft Hydraulic Oil 15 or 5606

• Exxon Univis J13

• Castrol Brayco Micronic 756

These fluid brands can be mixed together. Use of

hydraulic fluids with equivalent specifications to those

listed here are acceptable.

Weekly Maintenance

• Operate the dock leveler through the complete

operating cycle to maintain lubrication.

Note:

To thoroughly inspect the platform hinge area,

put the platform in the full below-dock position.

• Inspect the platform hinge and the lip hinge areas.

The hinge areas must be kept free of dirt and

debris. Build-up of foreign material in the hinge

areas will cause abnormal operation.

• Inspect warning decals and placards. Replace if

damaged or missing.

Use of fluids that do not have equivalent specifications

to those in the preceding list will result in abnormal

operation of the dock leveler and voiding of warranty.

A

B

D

C

«
...
30
31
32
33
34
...
»

Содержание LHP Series





















































Отзывы:

Нет отзывов

Похожие инструкции для LHP Series

TECHNOMIG 210 DUAL SYNERGIC

Бренд: Telwin Страницы: 176

Бренд: Vestil Страницы: 11

Бренд: Jacka Industries Страницы: 36

Бренд: RAPIBREW Страницы: 67

Бренд: Chicago Electric Страницы: 22

Бренд: Forney Страницы: 24

RAV6351 ILPVS1340

Бренд: rav Страницы: 152

Transcmig 250se

Бренд: CIGWELD Страницы: 41

Бренд: facelift Страницы: 8

Бренд: welldana Страницы: 7

Бренд: PowCon Страницы: 32

Бренд: Rotary Страницы: 64

Бренд: EWM Страницы: 56

Бренд: morse Страницы: 6

Бренд: morse Страницы: 6

Бренд: GALAGAR Страницы: 40

Бренд: Power Fist Страницы: 68

Бренд: Molift Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды