Poweramp LHP Series Скачать руководство пользователя страница 22

Страница: 22 / 52

4111-0012 — Sept. 2018

1. Mount the push-button control panel (

) so

bottom of control panel-to-dock floor distance (

) is

48 in. (1219 mm). See Figure 14.

2. Install electrical disconnect panel (

) if not already

installed. Disconnect panel supplied by others.

3. Install and connect the control wiring (see

drawings supplied with equipment).

4. Connect the dock leveler power cable to the field

wires in the pit junction box.

5. Seal the conduit in any location where the conduit

crosses over temperature zones that could produce

condensation.

Optional:

Install spacers between the wall and

enclosure to provide temperature insulation and air

flow. If the conduit could fill with water, a drip leg

may be needed.

6. Install placard (see page 22).

Install Control Panel and Wiring

DO NOT connect the dock leveler electrical wiring

and ground connections until all welding has been

completed.

DO NOT ground welding equipment to any hydraulic

or electrical components of the dock leveler. Always

ground welding equipment to the dock leveler frame,

NEVER to the platform.

Failure to follow these instructions may damage the

motor, hydraulics, wiring, and/or control panel.

Make sure that the power source has been locked

out and tagged according to OSHA regulations and

approved local electrical codes.

All electrical work — including the installation of the

disconnect panel, control panel, and final connections

to the pit junction box — must be performed by a

certified electrician and conform to all local and

applicable national codes.

Where indicated, all components must be connected

to a SAFETY EARTH GROUND that conforms to

the 1999 National Electrical Code Section 250-50

section (a) or section (c) for a grounding electrode

system.

1.50"

3.00"

Decal Size: 1.5 x 3

File Name: 1751-0736 Rev A

Arc Flash and

Shock Hazard

PPE [Personal Protection

Equipment] Required

De-energize equipment before

working on or inside. Do not

open cover without appropriate

PPE. Refer to NFPA 70E for

PPE requirements. This panel

may contain more than one

power source.

Hazardous Voltage

Will Result in Death

or Serious Injury

1751-0736 Rev A

A— Disconnect Panel

B— Control Panel

(provided by others)

C— Distance, 48 in. (1219 mm)

Figure 14

INSTALLATION

Содержание LHP Series





















































Результаты поиска

Содержание LHP Series

Отзывы:

Похожие инструкции для LHP Series

Бренды по названию

Популярные бренды

Poweramp LHP Series, Инструкция для владельца и пользователя

Результаты поиска

Содержание LHP Series

Отзывы:

Похожие инструкции для LHP Series

Бренды по названию

Популярные бренды