Poweramp LHP Series Скачать руководство пользователя страница 37

Страница: 37 / 52

4111-0012 — Sept. 2018

Symptom

Possible Cause

Solution

Three-phase units only:

Platform does not rise.

Motor hums, but does

not run.

No voltage is present on

one line.

NOTE: A motor that is

missing voltage on one line

is said to be single-phased.

Check for blown fuses at branch circuit disconnect.

Replace fuse. Determine cause of blown fuse.

Check motor starter as follows:

1. Disconnect wires at load side of starter.

2. Energize the starter.

3. Measure line-to-line voltage at line side of starter.

4. Measure line-to-line voltage at load side of

starter.

5. Line-side and load-side voltages should be

approximately the same. Replace starter if

voltage values are considerably different from

one another.

Check all wiring to motor for high resistance or no

connection.

Single-phase units only:

Platform does not rise.

Motor energizes, but

does not run.

Line voltage too low.

Check wiring to motor for high resistance. Check for

loose or corroded connections. Check if gauge of

wires to motor are of correct size and specification

for load requirement. Replace if necessary.

Faulty motor centrifugal

switch.

Replace motor.

Faulty motor capacitor.

Replace motor.

Platform does not

rise. Pump operates in

pressure relief mode.

Heavy object(s) on platform.

Remove object(s) from platform.

Note:

For safety reasons, the dock leveler is

designed to lift only the platform’s own weight.

Dock leveler binds.

Check for visible obstructions that could cause

binding. Remove obstructions. If no obstructions

found, contact Systems, LLC Technical Services.

Pressure relief set too low.

Increase pressure relief. See page 32 for instruction.

Note:

The pressure relief valve must not be set

at a level that causes the motor operating current

to exceed the full load amp value* at any time,

including when operating in pressure relief.

* The full load amp value can be found on the inside cover of the

control panel.

TROUBLESHOOTING

Содержание LHP Series





















































Результаты поиска

Содержание LHP Series

Отзывы:

Похожие инструкции для LHP Series

Бренды по названию

Популярные бренды

Poweramp LHP Series, Инструкция для владельца и пользователя

Результаты поиска

Содержание LHP Series

Отзывы:

Похожие инструкции для LHP Series

Бренды по названию

Популярные бренды