Poweramp LHP Series Скачать руководство пользователя страница 10

Страница: 10 / 52

4111-0012 — Sept. 2018

Technical Service at 800-643-5424 or [email protected]

This manual provides current information on the

LHP-series dock leveler. Due to ongoing product

improvement, some parts may have changed, along

with operation and troubleshooting methods. This

manual describes these changes where applicable.

The LHP-series dock leveler comes equipped

with an electrical control panel, which allows push

button operation of the dock leveler functions.

When combining a LHP-series dock leveler with a

Poweramp hydraulic vehicle restraint, the control

panel will allow for operation of both units in the same

control panel.

Each LHP-series dock leveler unit has been factory

tested to ensure satisfactory operation.

To illustrate which connections are to be made in the

field at installation, electrical drawings are included

with each order or by contacting Systems, LLC

Technical Services.

LHP dock levelers are available in the following sizes,

weight capacities, and options:

Width

6 ft (1828.8 mm)

6-1/2 ft (1981.2 mm)

7 ft (2133.6 mm)

Length

6 ft (1828.8 mm)

8 ft (2438 mm

10 ft (3048 mm)

Capacity (CIR*)

25,000 lb (11 340 kg)

35,000 lb (15 876 kg)

40,000 lb (18 144 kg)

* CIR (Comparative Industry Rating)

Call Poweramp to discuss available voltages, phases

and options to meet your specific needs.

General Information

Figure 3

INTRODUCTION

Содержание LHP Series





















































Результаты поиска

Содержание LHP Series

Отзывы:

Похожие инструкции для LHP Series

Бренды по названию

Популярные бренды

Poweramp LHP Series, Инструкция для владельца и пользователя

Результаты поиска

Содержание LHP Series

Отзывы:

Похожие инструкции для LHP Series

Бренды по названию

Популярные бренды