Polycom SoundPoint IP 200W Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 64

background image

Configuration File

A - 3

SIP_STUN_BINDTIME_
GUARD

uint16

1

positive integer,
units in seconds

default is 80

If STUN is enabled, this value specifies in
seconds how often the system will guard the
NAT bindings. Guarding for NAT bindings
helps the system to react properly if, for
example, the NAT device has been reset.

If this value is 0, no guarding will be made.
Also see
SIP_STUN_BINDTIME_DETERMINE.

SIP_STUN_BINDTIME_
DETERMINE

uint8

1

0 = disabled

1 = enabled (default)

If STUN is enabled and
SIP_STUN_BINDTIME_GUARD is defined,
setting this parameter to 1 forces the system
to automatically determining the duration of
NAT bindings in the system. In this case, the
SIP_STUN_BINDTIME_GUARD parameter
defines the initial test duration.

SIP_STUN_KEEP_ALIV
E_TIME

uint16

1

positive integer,
units in seconds

default is 90

If STUN is enabled,
SIP_STUN_KEEP_ALIVE_TIME defines in
seconds how often keep-alives are sent in
order to keep NAT bindings.

If SIP_STUN_BINDTIME_DETERMINE is
set to 1, SIP_STUN_KEEP_ALIVE_TIME
will be overruled and keep alives will be sent
with a frequency of half of determined
bindtime.

SIP_RTP_PRIORITY

uint8

1

positive integer

default is 0

Priority of RTP traffic based on the IP layer
ToS byte. See RFC 1349 for details.

“cost bit" is not supported.

•

Bit 7..5 defines precedence.

•

Bit 4..2 defines Type of Service.

•

Bit 1..0 are ignored.

Setting all three of bit 4..2 will be ignored.

SIP_RTP_PORT_RAN
GE

uint8

1

positive integer

default is 20

The number of ports that can be used for
RTP audio streaming.

SIP_RTP_PORT

uint16

1

port number

default is 5004

The first RTP port to use for RTP audio
streaming.

SIP_SIP_PORT

uint16

1

port number

default is 5060

Port used for first user agent (UA) instance.
Succeeding UA's will get succeeding ports.

Telephony Settings

VOIP_SETTINGS_PIN_
CODE

uint8

4

String consisting of 4
ASCII digits in the
range 0-9

default is 456

Configures the PIN code protecting the VoIP
settings menus on the handset.

Name

Type

Size

Permitted Values

Interpretation

«
...
47
48
49
50
51
...
»

Содержание SoundPoint IP 200W

































































Отзывы:

Нет отзывов

Похожие инструкции для SoundPoint IP 200W

Бренд: BT Страницы: 70

Бренд: Uniden Страницы: 40

Бренд: Radio Shack Страницы: 32

INDUCTION BATTERY CASE

Бренд: ANSMANN Страницы: 28

Бренд: DMGT Страницы: 3

Бренд: Uniden Страницы: 1

Бренд: Daewoo Страницы: 24

Бренд: Geemarc Страницы: 32

Бренд: Motorola Страницы: 200

Бренд: Motorola Страницы: 8

Бренд: Zte Страницы: 19

Бренд: Siemens Страницы: 22

Бренд: Telular Страницы: 64

Бренд: Telstra Страницы: 36

Бренд: Telongo Страницы: 3

Бренд: Festool Страницы: 26

Бренд: Festool Страницы: 132

OpenScape DECT Phone S6 Base

Бренд: Unify Страницы: 146

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды