background image

 Setting up Your System

3 - 9

10.

To force loading of the configuration file, press the 

OK

 key from the idle 

display, then select 

Settings > System Settings > Reset Gateway > Yes

 .

After the gateway is reset, it will pick up the new configuration file from 

the boot server. Look at the boot server or web administrator debug log to 

ensure the file is being sent.

11.

Configure the SoundPoint IP200W phone's call groups for inbound calls 

and default line for outbound calls by one of the following methods:

Method 1: Manual Configuration of Call Groups and Default Line

a

From the idle display, press the 

OK

 key, select the 

Settings

 menu, and 

then press the 

OK

 key again.

b

Select

 

Telephony settings

, press the 

OK

 key, select 

Call Groups

, and 

then press the 

OK

 key again.

Nicknames for the VoIP (and landline) accounts are listed. 

The configuration setting 

SUBSCR_0_SIP_UA_DATA_SIP_NAME_ALIAS sets the nicknames. 

Refer to 

Configuration File

 on page 

A-1

.

c

Select the VoIP lines that you want the current handset to receive calls 

on, and then press the 

OK

 key.

d

Press the 

End Call

 key.

e

Repeat step c for the VoIP lines that you want to the current handset 

to place calls on, and then press the 

OK

 key.

Warning

When a gateway is reset, any active calls on the SoundPoint IP 200W will suspend 
any reboot requests until the there is no active calls. The gateway will automatically 
reset 15 seconds after the last call. If the Call light is lit on the gateway, there are 
active calls.

Note

When the gateway is reset, it attempts to reload a configuration file each time.

Any settings made on the phone or through the web user interface are overwritten 
when a configuration file is loaded.

When the configuration file is loaded and a registration is successfully established, 
the VoIP indicator on the gateway turns red. The power indicator and the I-net 
indicator on the gateway remain red.

Note

By default, the SoundPoint IP 200W allows any phone to register to the gateway 
during the 5 minute registration interval when the reset button is pressed on the 
back of the gateway.

Содержание SoundPoint IP 200W

































































Отзывы: