Polycom SoundPoint IP 200W Скачать руководство пользователя страница 60

Страница: 60 / 64

Provisioning and Configuration Guide SoundPoint IP 200W

A - 14

Handset Default Primary Line Type - The primary line for eight handsets can be configured. The parameter
name for the primary line on handset 1 is shown.

USER_PRIMARY_LINE
_PP1

uint8

0 = PSTN

1 = VoIP line
(default)

Outgoing line selection (green button line).

Handset Default VoIP Line - Eight handsets can be mapped to their appropriate registration. The parameter
name for handset 1 is shown.

USER_VOIP_LINE_PP
1

uint8

1 to 8

1 = VoIP line 1
(default)

2 = VoIP line 2

3 = VoIP line 3

4 = VoIP line 4

5 = VoIP line 5

6 = VoIP line 6

7 = VoIP line 7

8 = VoIP line 8

Default VoIP line selection.

Emergency Primary Line

EMERGENCY_PRIMA
RY_PORT

uint8

0 to 8

0 = PSTN

1 = VoIP line 1
(default)

…

8 = VoIP line 8

Specifies the line to use when emergency
numbers are detected.

Scheduled Firmware Updates

FWU_POLLING_ENAB
LE

uint8

0 = disabled
(default)

1 = enabled

If set to 1, schedule firmware updates.

FWU_POLLING_MODE

uint8

0 = absolute

1 = relative to boot

Polling mode for firmware update.

FWU_POLLING_PERIO
D

uint32

positive integer,

units in seconds

default is 86400

Period to check for new firmware.

FWU_POLLING_TIME_
HH

uint8

0 - 23

default is 0

Hour for initiating the firmware update.

Note: Use this configurations parameter
together with FWU_POLLING_TIME_MM.

FWU_POLLING_TIME_
MM

uint8

0 - 59

default is 0

Minute for initiating the firmware update.

Note: Use this configurations parameter
together with FWU_POLLING_TIME_MM.

Name

Type

Size

Permitted Values

Interpretation

Содержание SoundPoint IP 200W

































































Результаты поиска

Содержание SoundPoint IP 200W

Отзывы:

Похожие инструкции для SoundPoint IP 200W

Бренды по названию

Популярные бренды

Polycom SoundPoint IP 200W, Руководство по настройке и конфигурации

Результаты поиска

Содержание SoundPoint IP 200W

Отзывы:

Похожие инструкции для SoundPoint IP 200W

Бренды по названию

Популярные бренды