Polycom SoundPoint IP 200W Скачать руководство пользователя страница 36

Страница: 36 / 64

Provisioning and Configuration Guide SoundPoint IP

4 - 4

Use configuration file to enable continuous logging and upload logs

in 5K chunks as the log buffer is filled.

%VOIP_LOG_AUTO_UPLOAD%:2

View the logs found in the

<Boot Server>/Log

directory.

<MAC ADDRESS>_MMDDHHMMSS.log

Log Format

The format of the log entries is shown below:

MMDDHHMMSS [level] [task identifier] Event description

The level of the log information can be one of the following values:

•

N = notice

•

W = warning

•

C = critical

•

E = error

The task identifier is a numeric value for the task which submitted the log

message.
A sample log is shown below:

0205232816 [N](10):DHCP Enabled

0205232816 [N](10):IP Address: 172.23.4.197

0205232816 [N](10):Gateway Address: 172.23.2.240

0205232816 [N](10):Subnet Mask: 255.255.0.0

0205232816 [N](10):TFTP boot server not set by DHCP. Using Static.

0205232816 [N](10):DHCP Discover completed

0205232816 [N](0f):Time Server: 172.23.0.235

0205232816 [N](0f):Boot server: venus.vancouver.polycom.com/Config/

Type: TFTP

0205232816 [N](17):BF Number of configurations parsed: 116

0205232816 [N](17):NSC Number of configurations parsed: 99

0205232816 [N](0f):RemCfg: Successful load of Config/00087b030148.cfg

from venus.vancouver.polycom.com

0205232816 [N](0f):RemCfg: Config File Flag Set..

0205232816 [N](09):VoipLan Gateway/07.94

0205232816 [N](09):MAC=00087B030148, SER= 00259, HW=12

0205232816 [N](09):Stun detection disabled

0205232816 [N](09):State info: 0

0205232816 [N](01):Error Log Fp (count=0, assertline=0)

0205232816 [N](01): Fp0: err=0, task=0

0205232816 [N](01): Fp1: err=0, task=0

0205232816 [N](01): Fp2: err=0, task=0

0205232816 [N](01):Error Log Bf (a=0, r=0, keepalive=0)

0205232816 [N](01): Bf0: t=0, l=0, f=, d=0,0,0,0,0,0

0205232816 [N](01): Bf1: t=0, l=0, f=, d=0,0,0,0,0,0

Содержание SoundPoint IP 200W

































































Результаты поиска

Содержание SoundPoint IP 200W

Отзывы:

Похожие инструкции для SoundPoint IP 200W

Бренды по названию

Популярные бренды

Polycom SoundPoint IP 200W, Руководство по настройке и конфигурации

Результаты поиска

Содержание SoundPoint IP 200W

Отзывы:

Похожие инструкции для SoundPoint IP 200W

Бренды по названию

Популярные бренды