manualshive.com logo in svg

POLIURS CV4.04, Инструкция по монтажу

Поделиться
Скачать
POLIURS CV4.04 Скачать руководство пользователя страница 36

HEATING MAIN MONTAGE INSTRUCTIONS  CV4.04 

 

      Addition Nr 1 

POLYOL (Component A) 

Extract from Safety information pages VI4.01 

1. Component parts:  

4-Methyl, 1-3 dioxolan-2-ones; CAS - 

№

 108-32-7; content 1-5% 

Benzyl dimetilamins;  CAS - 

№

 103-83-3; content 1-3% 

2. 

Risk identification:

  

Product isn’t qualified as hazardous.

 

3. 

Influence characteristics:

  

can cause irritation of respiratory ways, skin 

and eyes when come in contact with matter, when swallowed – feeling sick, 
vomiting, discomfort.

 

4. Work safety requirements: 

Hand protection: rubber gloves 

Eye protection:  protective glasses with side protection. 
Body protection: closed work clothes. 
General  safety  and  hygiene  measures:  store  away  from  food  and  beverages,  pet 

food and drinks. It is forbidden to eat, drink or smoke at the work place. Before 
breaks and after shift end clean hands and face. 

Storing: separately away from food and pet food. Keep in closed and dry space at 

temper15÷30

o

C. Do not allow any unsanctioned access and unforeseen 

mixing with isocyanat. 

5. First aid: 

General suggestions: remove all clothing that got soaked with this matter. 
When inhaled: If problems occur after breathing in of the vapor, then seek fresh air 

or medical attention if discomfort is present. 

When come in contact with skin: Carefully clean with soap and water. 

When  come  in  contact  with  eyes:  Razing  the  eye  brows  clean  eyes  at  least  15 

minutes  with big amounts of  water, seek medical attention if  discomfort doesn’t 
end. 

When swallowed: do not cause vomiting. Drink a lot of milk or water, seek medical 

attention. 

Do not allow  groundwater  penetration. Absorb  leaked matter  using  sand or similar 

material. Hand over waste according to local requirements. 

6. Fire safety procedures: 

Product is flammable and is not easy combustible. For putting out fire use foam or 

powder. After putting out fire cool down with water containers and not completely 
burned component. Use breathing device while putting out fire. 

7. R-phrase:  

R10 - flammable; R20/21/22 - hazardous to inhale, when comes in contact with skin 

or when swallowed. R34 – causes burns; R36 – irritates eyes; R52/53 – toxic for 
water organisms, can cause long term negative impact in water environment.

 

8. Additional information:

  

Safety information data page VI4.01.

 

Содержание CV4.04











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды