16
GROUND OUTPUT
This is a 500 mA constant ground output when the vehicle is running by remote. It becomes active 1 second before remote
Ignition ON, and shuts OFF as soon as a system shutdown is received. It can be used to activate external relays, bypass kits
or external Modules.
HOME VALET
(MODE 3 – FUNCTION 1, off by default.) When set on, this amazing safety feature allows the user to remotely place the
system into a no-start mode: if the vehicle is parked inDoors there is no danger it will start by accident by remote control or
External Trigger.
To activate Home Valet:
x
Press either the LOCK or the UNLOCK button;
x
Within 3 seconds, press and hold the STOP button until the Parking Lights go out.
To disable Home Valet, simply turn the Ignition Key ON.
NOTE:
Once Home Valet is activated, the vehicle will not start by remote control until the Ignition Key is turned ON.
PANIC MODE (in order to be available, this option must be programmed)
In an emergency situation, you can activate the Panic Mode. This will shut down the Engine and UNLOCK the Doors (if
UNLOCK is pressed) or LOCK the Door (if LOCK is pressed), disarm the Starter Kill and sound the Siren for 1 minute.
NOTE:
The Panic Mode can only be activated if the Horn is configured accordingly (Mode 3, Function 3, Option 3).
To activate the Panic Mode:
x
Press and hold the UNLOCK button for approximately 4 seconds until the Horn is triggered ON and the Parking
Lights flash; this will UNLOCK the Doors before the Horn is triggered.
x
Or press and hold the LOCK button for approximately 4 seconds until the Horn is triggered ON and the Parking
Lights flash; this will LOCK the Doors before the Horn is triggered.
The Panic Mode will automatically shut off after 1 minute.
NOTE:
If you want to stop the Panic Mode before the 1-minute delay, press the LOCK or UNLOCK button for
approximately 1 second.
QUICK LOCKOUT
Also called SECURE PANIC – for quick protection: the system will LOCK all Doors when Brake Pedal is pressed when the
Horn is sounding. (This features works only when Panic Mode has been activated.)
MULTI-CAR OPERATION
PS-3085 SH
systems allow for Multi-Car operation. This allows the owner of two Polarstart systems, installed on two
vehicles, to control both systems with one Transmitter. (Both vehicles must be equipped with a
PS-3085 SH
)
The remote Transmitter of the primary vehicle can control the Starter Disable system, the Door locks and the remote Car
Starter and TRUNK operation of the second vehicle. The remote Transmitter of the second vehicle can also operate the
primary vehicle
*To program a Transmitter for a second vehicle under Multi-Car operation, you must press
TRUNK + LOCK
buttons
simultaneously on that Transmitter in step 3 of the Transmitter code-learning procedure.
2
nd
CAR CONTROL (Press buttons simultaneously):
x
Press TRUNK + LOCK:
LOCK
x
Press TRUNK + UNLOCK:
UNLOCK
x
Press TRUNK + START:
START
x
Press TRUNK + STOP:
STOP
x
Press TRUNK + LOCK + UNLOCK:
AUX 3 (TRUNK)
RESETTING THE MODULE
The PS-3085 SH system is equipped with a reset function that allows the installer to erase all Transmitter codes and return all
programmed options to the factory defaults.
To reset the Module:
1. Ensure that the VALET & IGNITION are OFF.
x
Hold the Pin-Switch down for 4 sec. Release the Pin-Switch.
x
Immediately push and release pins-witch once again.
2. Press the VALET Switch 6 times.
3. Parking Lights will flash 8 times.
NOTE:
After a reset has been performed, the system sets all options back to default and erase all Transmitter codes.
(See
programming page for default option.)
Содержание PS-3085 SH
Страница 6: ...6 WIRING DIAGRAM ...
