manualshive.com logo in svg

Polaris SUPERSPORT 2006, Руководство пользователя

Polaris SUPERSPORT 2006 - высококачественный спортивный гидроскутер с максимальной производительностью. Для того чтобы ознакомиться с руководством по эксплуатации, скачайте бесплатное руководство на manualshive.com. Узнайте все возможности этого судна, загрузите инструкцию прямо сейчас!

Поделиться
Скачать
background image

9.2

BRAKES

HYDRAULIC BRAKE SYSTEM

OVERVIEW

The Polaris snowmobile hydraulic brake system consists of 
the following components or assemblies: brake lever, master 
cylinder, hydraulic hose, brake caliper (slave cylinder), brake 
pads, and a brake disc which is secured to the drive line.

When the hand activated brake lever (A) is applied, it contacts 
a piston (B) within the master cylinder. As the master cylinder 
piston moves inward it closes a small opening called a 
compensating port (C) within the cylinder and starts to build 
pressure within the brake system. As the pressure within the 
system is increased, the pistons (D) located in the brake 
caliper move toward the disc and applies pressure to the 
moveable brake pads. As the lever pressure is increased, the 
braking effect is increased.

The friction applied to the brake pads will cause the pads to 
wear. As the pads wear, the piston within the caliper self-
adjusts and moves further outward.

Brake fluid level is critical to proper system operation. A low 
fluid level allows air to enter the system causing the brakes to 
feel spongy.

COMPENSATING PORT

Located within the master cylinder is a small compensating 
port (C) which is opened and closed by the master cylinder 
piston assembly. The port is open when the brake lever is 
released and the piston is outward. As the temperature within 
the hydraulic system changes, this port compensates for fluid 
expansion caused by heat, or contraction caused by cooling. 
During system service, be sure this port is open. Due to the 
high temperatures created within the system during heavy 
braking, it is very important that the master cylinder reservoir 
have adequate space to allow for the brake fluid to expand. 
Master cylinder reservoirs should be filled to the top of the 
fluid level mark on the inside of the reservoir, 1/4” - 5/16” (.6 
-.8 cm) below lip of reservoir opening.

This system also incorporates a diaphragm (E) as part of the 
cover gasket and a vent port (F) located between the gasket 
and the cover. The combination diaphragm and vent allow for 
the air above the fluid to equalize pressure as the fluid 
expands or contracts. Be sure the vent is open and allowed to 
function. If the reservoir is overfilled or the diaphragm vent is 
plugged, the expanding fluid may build pressure in the brake 
system and lead to brake failure.

GENERAL GUIDELINES

Keep these points in mind when bleeding hydraulic brakes:

• The master cylinder reservoirs have limited capacities. 

It is easy to empty them during the bleeding procedure. 
This introduces air into the system which you are trying 
to purge. Watch the reservoir closely and add fluid 
when necessary to prevent air from entering the system.

• Apply only light to moderate pressure to the lever or 

pedal when bleeding the brake system. Extreme 
pressure will cause a surge of fluid through the small 
orifices of the brake system when the bleeder screw is 
opened and introduce air into the system by means of 
cavitation.

WARNING

Contaminated brake discs or brake pads greatly reduce 

braking performance and increase stopping distance. 

Do not attempt to clean contaminated pads. Replace 

them. Clean the brake disc with brake cleaner.
This brake system requires ethylene-glycol based fluid 

(DOT 4). Do not use or mix different types of fluid such 

as silicone-based or petroleum-based.
Do not use brake fluid taken from old, used or unsealed 

containers. Never reuse brake fluid. 
Keep brake fluid tightly sealed and out of reach of chil-

dren. Brake fluid can accumulate moisture, reducing it's 

effectiveness.
A soft, spongy feeling in the brake lever and/or brake 

pedal could indicate a hazardous condition in the brake 

system. Do not operate the motorcycle until the failure 

in the brake system is corrected.
An unsafe condition exists when air is trapped in the hy-

draulic brake system. Air in the brake hydraulic system 

acts like a soft spring and absorbs a large percentage 

of the pressure developed by the master cylinder. With-

out this pressure, the braking system cannot develop 

full braking force to allow for safe, controlled stops. It is 

extremely important to bleed the brakes properly after 

any brake system work has been performed or when in-

spection reveals spongy brakes.

CAUTION

Pressure bleeding is not recommended. When fluid 

surges through the fittings, it is possible to cavitate the 

fluid and create air in the system. In addition, the fluid 

stored in a pressure bleeder may be contaminated. Al-

ways use fresh DOT 4 brake fluid from a sealed con-

tainer.

Содержание SUPERSPORT 2006













































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPERSPORT 2006

Hammerhead Stingray Installation Reference Manual preview
Stingray
Бренд: Hammerhead Страницы: 11
Hammerhead SS250 Technical Manual preview
SS250
Бренд: Hammerhead Страницы: 70
Nakayama PD5230 Quick Start Manual preview
PD5230
Бренд: Nakayama Страницы: 14
American Sportworks CW-413 Operator'S Manual preview
CW-413
Бренд: American Sportworks Страницы: 105
Woodland Mills Woodlander Operator'S Manual preview
Woodlander
Бренд: Woodland Mills Страницы: 68
E-TON Viper 90R Owner'S Manual preview
Viper 90R
Бренд: E-TON Страницы: 134
Baja motorsports SD65 Sand Dog Setup Instructions preview
SD65 Sand Dog
Бренд: Baja motorsports Страницы: 8
Wilson Electronics 082614 Assembly Instructions preview
082614
Бренд: Wilson Electronics Страницы: 3
PRONAR T680 Operator'S Manual preview
T680
Бренд: PRONAR Страницы: 147
Polaris BRUTUS HD Operator'S Handbook Manual preview
BRUTUS HD
Бренд: Polaris Страницы: 14
Carrier Transicold X4 7300 Operation & Service Manual preview
Transicold X4 7300
Бренд: Carrier Страницы: 282
GAS GAS QUAD WILD HP 300 RV - 2005 Service Manual preview
QUAD WILD HP 300 RV - 2005
Бренд: GAS GAS Страницы: 72
GAS GAS K2 QUAD 50 User Manual preview
K2 QUAD 50
Бренд: GAS GAS Страницы: 36
Camoplast 1099-01-1105 User Manual preview
1099-01-1105
Бренд: Camoplast Страницы: 55
Yamaha YFM700RV 2009 Service Manual preview
YFM700RV 2009
Бренд: Yamaha Страницы: 409
Yamaha SL338D Service Manual preview
SL338D
Бренд: Yamaha Страницы: 112
Yamaha YFM250XL(C) Service Manual preview
YFM250XL(C)
Бренд: Yamaha Страницы: 398
Yamaha GRIZZLY 350 2016 Installation Manual preview
GRIZZLY 350 2016
Бренд: Yamaha Страницы: 140

Бренды по названию

Популярные бренды

Загрузить еще бренды