manualshive.com logo in svg

Polaris SUPERSPORT 2006, Руководство пользователя

Polaris SUPERSPORT 2006 - высококачественный спортивный гидроскутер с максимальной производительностью. Для того чтобы ознакомиться с руководством по эксплуатации, скачайте бесплатное руководство на manualshive.com. Узнайте все возможности этого судна, загрузите инструкцию прямо сейчас!

Поделиться
Скачать
background image

6.28

ENGINE

340/550 ENGINE DISASSEMBLY

NOTE:  Inspect all parts for wear or damage during 
disassembly. Replace all seals, o-rings, and gaskets 
with Genuine Pure Polaris parts during assembly. 
Refer to the ‘INSPECTONS” on page 3.5 for general 
inspection procedures.

1.

Disconnect the coil pack from the recoil cover and the
wiring harness.

2.

Loosen the carburetor clamps (1) and remove the
carburetors from the mounting boots.

3.

Note where the oil lines are routed and remove the oil lines
from the carburetors.

4.

Remove the carburetor mounting boots (2) from the
cylinders.

5.

Remove both the cylinder head (3) and the exhaust side
fan (4) shrouds from the engine assembly.

6.

After removing the fan shrouds, take note of the vibration
dampener (5) located between the cylinders month intake
side.

7.

Remove the CDI from the flywheel cover.

8.

Remove the flywheel cover (6).

9.

Remove the recoil cup (7).

10. Hold the flywheel with the holding wrench PN 8700229

and remove the flywheel nut and washer.

11. Using a flywheel puller (PN 2871043), remove the

flywheel (8) from the engine. Do not install the puller bolts
in amy more than 5/16

”

 of an inch/7.9mm into the

flywheel threads or stator damage may result.

12. Remove the flywheel and woodruff key.

13. Remove the stator plate. 

14. Remove the oil pump (9). Note the o-ring and shim

placement.

15. Remove the cylinder head bolts (10).

16. Remove the cylinder head (11).

17. Remove the head gasket (12). During the removal process

note that the gasket has a EX for exhaust side and UP for
the orientation.

18. Remove the cylinder base nuts (13) and carefully remove

each cylinder.

19. Remove the reed valve assembly (14) from the crankcase.

20. Remove the wrist pin c-clips

21. Using a piston pin puller (PN 2870386) remove the wrist

pins from the pistons.

22. Turn the crankcase over and remove the crankcase bolts

(15).

23. Carefully turn the case back over and separate the case

halves.

24. Remove the crankcase seals (16).

25. Remove the oil pump bushing, spacer, and cross shaft (17)

and inspect for any wear or damage.

340/550 ENGINE ASSEMBLY

1.

Insert the oil pump cross shaft, spacer and bushing.

2.

Install a new o-ring on the oil pump.

3.

Place the oil pump aside for later installation.

4.

Set the crankshaft into the lower case half.

NOTE:  Make sure that the crankshaft rotates 
smoothly and does not bind. Rotate the bearings so 
that the anti-rotation pins are testing in their 
appropriate galleries.

5.

Apply 3-Bond (PN 2871557) sealer to the top half of the
crankcase.

6.

Apply Polaris 2-Stroke engine oil to the oil pump cross
shaft in the lower half of the crankcase.

7.

Install new crankcase oil seals.

8.

Match up the top half of the crankcase to the lower case
and hold the case halves together and turn it upside down.

9.

Install the crankcase bolts and torque to 18 ft-lb (25Nm).
in the pattern shown below.

10. Turn the crankcase over an install the pistons with the

arrow on the piston crown facing the flywheel (MAG)
side. This will orientate the piston so that the piston ring
locating pins will be in the intake side of the engine.

11. Apply Polaris 2-Stroke engine oil to the wrist pins and the

small end bearings and install them onto the crankshaft
with the piston installation tool (PN 2830386).

12. Lubricate rings and the pistons with Polaris 2-Stroke oil

and install the rings with the letter, mark or beveled side
facing upward.

13. Install the c-clips into the piston so that the opening of the

“C” is positioned at the 12:00 or 6:00 position.

14. Install the reed valves in to the intake of the crankcase.

15. Install new base gaskets.

16. Compress the piston rings and install each cylinder onto

the crankcase.

5

9

1

12

8

4

3

2

7

6

11

12

CRANKCASE TORQUE PATTERN-FUJI

Содержание SUPERSPORT 2006













































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPERSPORT 2006

Kazuma Panda Owner'S Manual preview
Panda
Бренд: Kazuma Страницы: 34
Arctic Cat 650 MUD PRO 2011 Operator'S Manual preview
650 MUD PRO 2011
Бренд: Arctic Cat Страницы: 84
Yamaha YFZ45RB Owner'S Manual preview
YFZ45RB
Бренд: Yamaha Страницы: 156
Yamaha YFZ45YSXH Owner'S Manual preview
YFZ45YSXH
Бренд: Yamaha Страницы: 154
Ski-Doo Tundra Series Operator'S Manual preview
Tundra Series
Бренд: Ski-Doo Страницы: 159
Ski-Doo 2006 Mini Z Operator'S Manual preview
2006 Mini Z
Бренд: Ski-Doo Страницы: 103
IBEA IBT 5000 Series User And Maintenance Manual preview
IBT 5000 Series
Бренд: IBEA Страницы: 56
Duralite AL15 Owner'S And Operator'S Manual preview
AL15
Бренд: Duralite Страницы: 27
BMS APU08E Owner'S Manual preview
APU08E
Бренд: BMS Страницы: 158
TGB Blade 525 Service Manual preview
Blade 525
Бренд: TGB Страницы: 209
Yamaha SRX700G Owner'S Manual preview
SRX700G
Бренд: Yamaha Страницы: 84
Yamaha STAR 2015 Owner'S Manual preview
STAR 2015
Бренд: Yamaha Страницы: 106
Yamaha RX10RTW Owner'S Manual preview
RX10RTW
Бренд: Yamaha Страницы: 100
Yamaha RX10LTX Owner'S Manual preview
RX10LTX
Бренд: Yamaha Страницы: 98
Yamaha RX10MSW Owner'S Manual preview
RX10MSW
Бренд: Yamaha Страницы: 108
Yamaha RX10J Owner'S Manual preview
RX10J
Бренд: Yamaha Страницы: 101
Yamaha SRX700D Service Manual preview
SRX700D
Бренд: Yamaha Страницы: 497
Yamaha RX10H Service Manual preview
RX10H
Бренд: Yamaha Страницы: 683

Бренды по названию

Популярные бренды

Загрузить еще бренды