manualshive.com logo in svg

Polaris SUPERSPORT 2006, Руководство пользователя

Polaris SUPERSPORT 2006 - высококачественный спортивный гидроскутер с максимальной производительностью. Для того чтобы ознакомиться с руководством по эксплуатации, скачайте бесплатное руководство на manualshive.com. Узнайте все возможности этого судна, загрузите инструкцию прямо сейчас!

Поделиться
Скачать
background image

11.26

REAR SUSPENSION

remove as much dirt and grime as possible by scrubbing
with a soft bristle brush. Never pressure wash your shock,
as this can force water and debris inside which will
damage the seals. Dry the shock assembly with
compressed air, if available, or use clean towels.

5.

Use a 3/32" Hex Key to remove the button head screw
from the FOX air valve in the shock body.

6.

Securely clamp Fox Nitrogen Safety Needle in vice.

7.

Insert the Fox Safety Needle squarely into center of gas
valve. 

8.

Using a blunt object, depress the air valve core to release
pressure.

9.

When the shock is FULLY DISCHARGED, pull reservoir
away from the Fox Safety Needle in a straight, smooth
motion.

10. Clamp the body end eyelet of the shock securely in vice

with shaft side up.

11. Using the 1 3/8

"

 wrench, loosen and unscrew the bearing

assembly from the shock body. If the body cap unscrews
instead of the bearing, that is OK. You will need to remove
both for this rebuild procedure.

12. Clamp the shock in the vice using the body clamp blocks.

If the bearing is still in the body, use the 1 3/8” end wrench
to loosen and unthread the bearing. If the body cap is what
needs removal, use the large crescent wrench to loosen
and unthread the body cap.

13. Remove the shaft assembly from the body tube, and place

on a clean, lint free paper towel. Remove the shock from
the vice and pour shock oil from body tube into a proper
disposal container. Do not re-use old shock oil.

14. Using the handle of the mallet, push the IFP out of the

shock body on to a folded shop towel. 

15. Remove the bleed screw from the IFP using the 1/8" T-

Handle

16. Clean the IFP with solvent. Dry with compressed air in a

well ventilated area. If compressed air is not available, dry
parts using clean, lint free paper towels and let sit in a well
ventilated area to allow the solvents to evaporate.

17. Set body assembly aside on a clean, lint free towel.

18. Clamp the shaft eyelet securely in vice with the piston end

up.

19. Using a 9/16" wrench, remove the piston lock nut from the

end of the shaft.

20. Hold the tip of the Phillips Head Screwdriver against the

end of shaft. Hold the piston assembly under the top-out

plate and lift upwards. Slide the piston assembly onto the
shaft of the screwdriver. Pull the Screwdriver away from
shock shaft while supporting the piston assembly. Set this
on a clean, lint free towel. There are many pieces to the
piston assembly, and the assembly order of these pieces is
critical to the proper performance of your shock. This step
ensures that the proper order is kept. 

21. Slide bearing assembly off of shaft. Use extreme caution

not to scratch inside of the bearing assembly when passing
it over the threads at end of shaft and set it on a clean, lint
free towel.

22. Remove the bleed screw from the IFP and set them both

on a clean, lint free towel. 

FOX PS-5 ASSEMBLY

1.

Using a small pair of snap ring pliers, remove the snap ring
from the bearing housing. Using your fingers, remove the
FIST scraper from the housing. Use a scribe or a dental
pick to remove the o-ring from the inside of the FIST
scraper by "spearing" the seal with the point of the scribe
and pulling it out. Use extreme caution when using a
scribe to remove seals. Always "spear" the seal with the
point of the scribe. Do not wedge the point of the scribe in
behind the seal. This can scratch the surface of the seal
groove which will compromise the performance and
reliability of the shock absorber.

2.

Use the scribe to remove the u-cup wiper and o-ring seals
from the bearing housing. Be careful not to scratch the seal
grooves or the DU bushing that is pressed into the bearing. 

3.

Thoroughly clean the FIST scraper, bearing housing, and
piston assembly with solvent. Dry with compressed air in
a well ventilated area. If compressed air is not available,
dry parts using clean, lint free paper towels and let sit in a
well ventilated area, to allow the remaining solvent to
evaporate.

4.

Use a scribe or dental pick to remove the o-ring seal from
the IFP.

5.

Install the new, well lubricated, o-ring into the FIST
scraper. Check to make sure the seal is properly seated,
and is not twisted. If a tool is required to aid in proper
seating of o-ring, use the non-writing end of a pen, or a
similar soft, blunt object, to push it in.

6.

Install the new, well lubricated, o-rings into the bearing
housing. Correct placement of the shaft seal o-ring is in the
groove next to the DU bushing. Check to make sure the
seals are properly seated, and are not twisted. If a tool is
required to aid in proper seating of o-ring, use the non-
writing end of a pen, or a similar soft, blunt object, to push
it in.

7.

Install the new U-cup seal into bearing. U-cup should be
installed so the cupped end is facing the DU bushing
inside of bearing. Check to make sure seal is properly

CAUTION

Point air valve away from face and body when charging 

or discharging any shock.

Содержание SUPERSPORT 2006













































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPERSPORT 2006

Taylor-Dunn SC-100-24 Service And Replacement Parts Manual preview
SC-100-24
Бренд: Taylor-Dunn Страницы: 126
Etnyre PAVER SPECIAL RPS Series Parts And Operation Manual preview
PAVER SPECIAL RPS Series
Бренд: Etnyre Страницы: 61
Can-Am Maverick Sport 1000 2021 Operator'S Manual preview
Maverick Sport 1000 2021
Бренд: Can-Am Страницы: 195
Harbor Freight Tools OneStopGardens 91240 Assembly And Operating Instructions Manual preview
OneStopGardens 91240
Бренд: Harbor Freight Tools Страницы: 7
Valor 54TS Owner'S Manual preview
54TS
Бренд: Valor Страницы: 66
Baja motorsports Baja 90cc Owner'S Manual preview
Baja 90cc
Бренд: Baja motorsports Страницы: 77
Yamaha SL338D Service Manual preview
SL338D
Бренд: Yamaha Страницы: 112
Yamaha YFM250XL(C) Service Manual preview
YFM250XL(C)
Бренд: Yamaha Страницы: 398
Yamaha VX600ERC Owner'S Manual preview
VX600ERC
Бренд: Yamaha Страницы: 87
Yamaha GRIZZLY 350 2016 Installation Manual preview
GRIZZLY 350 2016
Бренд: Yamaha Страницы: 140
Daymak Sasquatch 800 UTV Owner'S Manual preview
Sasquatch 800 UTV
Бренд: Daymak Страницы: 16
Ammann AP 240 Operating Manual preview
AP 240
Бренд: Ammann Страницы: 170
Rosco Maximizer 3B Operation And Service Manual preview
Maximizer 3B
Бренд: Rosco Страницы: 364
Combi-Camp COUNTRY VALLEY Instruction Book preview
COUNTRY VALLEY
Бренд: Combi-Camp Страницы: 20
Moni ABARTH 500 Assetto corse Instruction Manual preview
ABARTH 500 Assetto corse
Бренд: Moni Страницы: 25

Бренды по названию

Популярные бренды

Загрузить еще бренды