manualshive.com logo in svg

Polaris SUPERSPORT 2006, Руководство пользователя

Polaris SUPERSPORT 2006 - высококачественный спортивный гидроскутер с максимальной производительностью. Для того чтобы ознакомиться с руководством по эксплуатации, скачайте бесплатное руководство на manualshive.com. Узнайте все возможности этого судна, загрузите инструкцию прямо сейчас!

Поделиться
Скачать
background image

7.7

CLUTCHING

DRIVE SYSTEM TERMINOLOGY

SYSTEM OVERVIEW

The Polaris drive system is a centrifugally actuated variable 
speed belt drive unit. The drive clutch, driven clutch, and belt 
make up the torque converter system. Each clutch comes from 
the factory with the proper internal components installed for 
its specific engine model. Therefore, modifications or 
variations of components at random are never recommended. 
Proper clutch setup and adjustments of existing components 
must be the primary objective in clutch operation diagnosis.

DRIVE SPRING

The drive spring opposes the shift force generated by the 
clutch weights, and determines the neutral RPM, engagement 
RPM, and wether the engine RPM remains flat, rises, or falls 
during shift out. When changing only the drive spring, 
installing a spring with a lower pre-load rate will result in a 
lower engagement RPM speed, while installing a spring with a 
higher pre-load rate will result in a higher engagement RPM. 

CLUTCH WEIGHT

The clutch weights generate centrifugal force as the drive 
clutch rotates. The force generated changes in relation to the 
engine RPM and with specified weight of each clutch weight. 
When changing only the clutch weights, a lighter weight will 
result in a higher engagement RPM, lower shifting force, and 
higher shift out RPM. Installing heavier weights has the 
opposite effect

NEUTRAL SPEED

Engine RPM when the force generated by the clutch weights is 
less than the pre-load force generated by the drive spring. In 
this mode, the drive clutch is disengaged.

ENGAGEMENT RPM

Engine RPM when the force generated by the clutch weights 
overcomes the drive spring pre-load force and the moveable 
sheave begins to close or “pinch" the drive belt. The 
engagement mode continues until no more belt slippage occurs 
in the drive clutch. Once 100% belt engagement is achieved, 
the sled will accelerate along the low ratio line until the drive 
clutch up shift force overcomes the opposing shift force 
generated by the driven clutch.

SHIFT OUT OVERREV

Engine RPM that spikes above the desired operating RPM 
speed. The shift out RPM should come down to the desired 
operating RPM, but never below, after the driven clutch begins 
to open.

SHIFT OUT RPM

Engine RPM at which the up shift force generated by the drive 
clutch overcomes the shift force within the driven clutch. In 
this mode, the drive clutch will move the belt outwards, and 
the driven clutch will allow the drive belt to be pulled down 
into the sheaves.

During WOT operation, the shift out RPM can be seen as the 
maximum, sustained RPM displayed on the tachometer. The 
shift out RPM should be the same RPM as the recommended 
engine operating RPM. If the shift out RPM is above the 
recommended engine operating RPM, install heavier drive 
clutch weights. If the shift out RPM is below the 
recommended engine operating RPM, install lighter drive 
clutch weights.

The shift out RPM should remain constant during both the 
upshift and back shift modes.

DRIVEN SPRING

A compression spring (Team driven clutch) or torsional spring 
(Polaris P-85 driven clutch) works in conjunction with the 
helix, and controls the shift rate of the driven clutch. The 
spring must provide enough side pressure to grip the belt and 
prevent slippage during initial acceleration. A higher spring 
rate will provide more side pressure and quicker back shifting 
but decreases drive system efficiency. If too much spring 
tension exists, the driven clutch will exert too much force on 
the belt and can cause premature belt failure.

CAUTION

All clutch maintenance repairs must be performed only 

by an authorized Polaris service technician who has at-

tended a Polaris sponsored service training seminar 

and understands the proper procedures as outlined in 

this manual. Because of the critical nature and preci-

sion balance incorporated into the drive clutch, it is ab-

solutely essential that no attempt at clutch disassembly 

and/or repair be made without factory authorized spe-

cial tools and service procedures. Any unauthorized 

modifications to clutches, such as adding or removing 

weights, will void the warranty

.

Содержание SUPERSPORT 2006













































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPERSPORT 2006

Massimo Motor 800UTV-EC User Manual preview
800UTV-EC
Бренд: Massimo Motor Страницы: 165
Yamaha BIG BEAR YFM400NN Owner'S Manual preview
BIG BEAR YFM400NN
Бренд: Yamaha Страницы: 161
Yamaha BIG BEAR YFM400NC Owner'S Manual preview
BIG BEAR YFM400NC
Бренд: Yamaha Страницы: 162
Yamaha BANSHEE YFZ350Y Owner'S Manual preview
BANSHEE YFZ350Y
Бренд: Yamaha Страницы: 142
Yamaha Big Bear 400 YFM40FBB Owner'S Manual preview
Big Bear 400 YFM40FBB
Бренд: Yamaha Страницы: 156
Yamaha Big Bear 250 Owner'S Manual preview
Big Bear 250
Бренд: Yamaha Страницы: 156
Yamaha BEARTRACKER YFM250XN Owner'S Manual preview
BEARTRACKER YFM250XN
Бренд: Yamaha Страницы: 156
Yamaha BANSHEE YFZ350 Owner'S Manual preview
BANSHEE YFZ350
Бренд: Yamaha Страницы: 140
Yamaha BIG BEAR 4X4 Owner'S Manual preview
BIG BEAR 4X4
Бренд: Yamaha Страницы: 167
Yamaha BIG BEAR YFM400FWS Owner'S Manual preview
BIG BEAR YFM400FWS
Бренд: Yamaha Страницы: 173
Yamaha BANSHEE 350 YFZ350Z Owner'S Manual preview
BANSHEE 350 YFZ350Z
Бренд: Yamaha Страницы: 146
Yamaha BearTracker Owner'S Manual preview
BearTracker
Бренд: Yamaha Страницы: 163
Yamaha big bear 350 Owner'S Manual preview
big bear 350
Бренд: Yamaha Страницы: 170
Yamaha BANSHEE 350 YFZ350A Owner'S Manual preview
BANSHEE 350 YFZ350A
Бренд: Yamaha Страницы: 148
Yamaha BIG BEAR 400 Owner'S Manual preview
BIG BEAR 400
Бренд: Yamaha Страницы: 176
Yamaha BANSHEE YFZ350R Owner'S Manual preview
BANSHEE YFZ350R
Бренд: Yamaha Страницы: 168
Yamaha BANSHEE YFZ350P Owner'S Manual preview
BANSHEE YFZ350P
Бренд: Yamaha Страницы: 168
Yamaha BANSHEE 350 Owner'S Manual preview
BANSHEE 350
Бренд: Yamaha Страницы: 169

Бренды по названию

Популярные бренды

Загрузить еще бренды