Polaris 340 Edge Скачать руководство пользователя страница 129

Страница: 129 / 157

126

MAINTENANCE

Extended Storage

Bearings

Grease the jackshaft and drive shaft clutch side bearings with Polaris

Premium All-Season Grease or a similar high quality grease to prevent

corrosion.

Clutch and Drive System

Remove the drive belt and store in a cool dry location. Lubricate the

sheave faces of the drive and driven clutches with a light coat of oil or

Polaris Cable Lubricant.

Do not lubricate clutch components, except the driven clutch shaft bush-

ing as outlined in the Master Repair Manual. See your dealer.

Engine and Carburetor Protection

Proper preparation of the engine and fuel system is vital to the preven-

tion of rust and corrosion on precision engine parts during storage.

Whenever the machine is stored for a period of more than 60 days, the

engine must be fogged with fogging oil. Follow the engine fogging

instructions provided on the container.

Always add Premium Carbon Clean or a fuel conditioner/stabilizer to

the fuel tank. Follow the instructions on the container, running the

engine for five minutes to get additives through the entire fuel system.

Top off with fresh fuel.

If stabilizer is not used, drain the carburetors by removing the water trap

drain plugs. See page 97.

NOTE:

Jet restriction caused by improper storage can cause lean con-

ditions and very poor slow speed driving quality.

Содержание 340 Edge






























































































































































Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды

Polaris 340 Edge, Руководство пользователя

Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды