Polaris 340 Edge Скачать руководство пользователя страница 126

Страница: 126 / 157

123

MAINTENANCE

Steering System

Ski Skags

Check skags before each use of the snowmobile to ensure positive steer-

ing characteristics. Skags must be replaced when worn to half their orig-

inal diameter.

NOTE:

Carbide skags must be replaced if

any

abnormal wear or chip-

ping is found.

Skag Replacement

1. Raise and support the front of the machine so the skis are approxi-

mately 6

(15.2 cm) from the ground.

2. Remove the attaching nuts and pry the skag downward.
3. Remove the rear end of the skag.
4. Remove the front end of the skag.
5. Reverse the steps to install a skag.

WARNING

Worn skis and/or skags will adversely affect handling. Loss of vehicle control

may result, causing serious injury or death.
See your dealer's studding chart for recommended skags. If you install

longer or more aggressive carbide skags than the original equipment, it may

also be necessary to add track studs to maintain proper vehicle control while

turning on hard-packed snow or ice.

Содержание 340 Edge






























































































































































Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды

Polaris 340 Edge, Руководство пользователя

Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды