Polaris 340 Edge Скачать руководство пользователя страница 63

Страница: 63 / 157

PRE-RIDE INSPECTIONS

Before Starting the Engine

Park Brake Lever Lock

Use the park brake lever lock only when you want the machine to

remain stationary; for example, when parked on an incline for a period

of five minutes or less.

1. Brake Lever
2. Park Brake Lever Lock

(if equipped)

3. Master Cylinder Reser-

voir/ Cover

4. Fluid Level Indicator

Lock Engagement

To engage the lock, squeeze

the brake lever tightly and

push forward on the lock.

Hold the lock forward while

releasing the brake lever.

NOTE:

If the brake lever is

squeezed tightly enough, the lock will move freely into place.

Do not force the lock or it may break.

The brake light on the console will light up if the park brake lever lock

is set while the engine is running. It will also be lit when the service

brake is in use. If the park brake light does not come on when the park

brake or service brake is in use, have it serviced by your dealer.

Lock Release

To release the lock, squeeze the brake lever tightly and release it. The

lock will return to the unlock position.

WARNING

If the park brake lever lock is partially or entirely engaged while riding, the

brakes may overheat, resulting in brake damage. In extreme cases it could

cause a fire, which could result in serious injury or death. Always ensure that

the lever lock is completely disengaged before operating the snowmobile.

3 4

Содержание 340 Edge






























































































































































Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды

Polaris 340 Edge, Руководство пользователя

Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды