Polaris 340 Edge Скачать руководство пользователя страница 96

Страница: 96 / 157

MAINTENANCE

General Maintenance

Spark Plugs

A new engine can cause temporary spark plug fouling due to the preser-

vative added during the assembly process. Avoid prolonged idle speeds,

which cause plug fouling and carbonization. Refer to your Owner's

Manual Supplement for the specific spark plug to be used in your

machine.

Spark plug condition is indicative of engine operation. The spark plug

firing end condition should be read after the engine has been warmed up

and the vehicle has been driven at higher speeds. Immediately check the

spark plug for correct color.

NOTE:

Incorrect fuel mixture can often cause a spark plug to appear

too dark or too light in color. Before changing spark plug heat

ranges, be sure the correct main jet is installed in the carbure-

tor(s). Refer to the Owner's Manual Supplement or see your

dealer.

CAUTION

Using non-recommended spark plugs can result in serious engine damage.

A spark plug with a heat range too high will always cause engine damage if

the engine is operated in conditions more severe than intended for that plug.

Always use the spark plugs recommended for your snowmobile. See your

Owner’s Manual Supplement.
•

Use recommended spark plugs with the proper gap.

•

Torque spark plugs to 18-22 ft. lbs. (24-30 Nm).

•

Always carry spare spark plugs.

WARNING

A hot exhaust system and engine can cause serious burns. Wear protective

gloves when removing a spark plug for inspection.

Содержание 340 Edge






























































































































































Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды

Polaris 340 Edge, Руководство пользователя

Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды