Polaris 340 Edge Скачать руководство пользователя страница 117

Страница: 117 / 157

114

MAINTENANCE

General Maintenance

Drive Belt Deflection

Measure belt deflection with

both clutches at rest and in

their full neutral position.

Place a straight edge (1) on the

belt and apply downward pres-

sure while measuring at point

2. This measurement should be

1 1/4

(3.2 cm).

Drive Belt Adjustment

Standard Clutch

Belt deflection can be adjusted without removing the clutch from the

jackshaft.

1. Pull the belt into the driven clutch to slightly open the sheaves.
2. Loosen the three bolts on the adjustment cam and turn the cam

counterclockwise to reduce the distance between the sheaves.

not rotate past the #1 position.

3. Torque the bolts to 4-6 ft. lbs. (5.4-8 Nm)

TEAM Clutch

1. Loosen the 7/16

jam nut on the belt width adjuster.

2. Using a 1/8

Allen wrench, adjust the threaded set screw as needed.

NOTE:

Turn the set screw in (clockwise) to increase the distance

between the sheaves and out (counterclockwise) to decrease

the distance.

3. Tighten the jam nut.

Содержание 340 Edge






























































































































































Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды

Polaris 340 Edge, Руководство пользователя

Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды