Polaris 340 Edge Скачать руководство пользователя страница 97

Страница: 97 / 157

MAINTENANCE

General Maintenance

Spark Plugs

1. Normal

The normal insulator tip is gray, tan or light brown. There will be few

combustion deposits. The electrodes are not burned or eroded. This

indicates the proper type and heat range for the engine and the service.

NOTE:

The tip should not be white. A white insulator tip indicates

overheating, caused by use of an improper spark plug or incor-

rect carburetor/throttle body adjustments.

2. Wet Fouled

The wet fouled insulator tip is black. A damp oil film covers the firing

end. There may be a carbon layer over the entire nose. Generally, the

electrodes are not worn. General causes of fouling are excessive oil, use

of non-recommended injection oil, improper use of the choke, or incor-

rect carburetion adjustments.

Spark Plug Removal and Replacement

1. Remove the spark plug cap.
2. Using the special wrench provided in

the tool pouch, rotate the spark plug

counterclockwise to remove.

3. Reverse the procedure for spark plug

installation.

4. Torque the spark plug to specification.
5. Reinstall the spark plug cap.

Содержание 340 Edge






























































































































































Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды

Polaris 340 Edge, Руководство пользователя

Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды