Polaris 340 Edge Скачать руководство пользователя страница 109

Страница: 109 / 157

106

MAINTENANCE

General Maintenance

Headlight Adjustment

The headlight may be adjusted for vertical aim using the following pro-

cedure.

1. Place the snowmobile on a level surface with the headlight approxi-

mately 25 feet (7.6 m) from a wall.

2. Measure the distance from the floor to the center of the headlight

and make a mark on the wall.

3. Start the engine and turn the headlight switch to high beam.
4. Observe the headlight aim. The most intense part of the headlight

beam should be aimed 2

(5.1 cm) below the mark placed on the

wall.

NOTE:

Rider weight must be included on the seat.

5. Turn the adjustment nut (

✪

), located inside the hood, just below the

headlamp opening. Turn the knob in or out as needed for proper

aim.

(5.1 cm)

✪

Lamp Center Height

25 ft. (7.6 m)

Содержание 340 Edge






























































































































































Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды

Polaris 340 Edge, Руководство пользователя

Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды