Polaris 340 Edge Скачать руководство пользователя страница 139

Страница: 139 / 157

136

TROUBLESHOOTING

EDGE Suspension Troubleshooting

Problem

Solution

Rear suspension bot-

toms too easily

• Increase torsion spring preload
• Increase rear shock compression damping by turning

screw clockwise

• Increase torsion spring wire diameter (see your dealer)

Rides too stiff in rear

• Check for binding suspension shafts and grease all pivot

points

• Decrease torsion spring preload adjustments
• Decrease rear shock compression valving by turning

screw counterclockwise (if equipped with optional Indy

Select shock)

• Change to lighter valving if (if equipped with FOX

shocks)

• Check for proper track tension

Machine darts from

side to side

• Make sure skis are aligned properly
• Make sure spindles and all steering components are free

turning

• Make sure skags are straight on skis
• Check rail slide and replace if worn
• Reduce ski pressure:

A) Reduce IFS spring preload
B) Reduce rear torsion spring preload

Front end pushes

• Check for worn skags
• Check for binding suspension shafts and grease all pivot

points

• Increase IFS spring preload by adjusting cam or threaded

adjuster

• Decrease front limiter strap length

Steering is heavy

• Check ski alignment
• Check skags and skis for damage
• Reduce ski pressure:

A) Increase front track spring preload
B) Reduce IFS spring preload by adjusting cam
C) Reduce rear torsion spring preload

Setting up for deep

snow operation

• Change worn Hi-fax
• Move front track shock assembly to upper position

Содержание 340 Edge






























































































































































Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды

Polaris 340 Edge, Руководство пользователя

Результаты поиска

Содержание 340 Edge

Отзывы:

Похожие инструкции для 340 Edge

Бренды по названию

Популярные бренды