background image

ALLG./BA SEITE 2 /  9300-GB

Important information concerning Product Liability.

According to the laws governing product liability, the manufacturer and dealer are
obliged to hand the operating manual to the customer at the time of sale, and to
instruct them in the recommended operating, safety, and maintenance regulations.
Confirmation is necessary to prove that the machine and operating
manual have been handed over accordingly.
For this purpose, document A is to be signed and sent to Pöttinger,
document B remains with the dealer supplying the machine, and the
customer receives document C.

Attention!

 Should the customer resell the machine at a later date, the operating

manual must be given to the new owner who must then be instructed in the
recommended regulations referred to herein.

GB

Dear Farmer

You have just made an excellent choice. Naturally we
are very happy and wish to congratulate you for
having chosen Pöttinger. As your agricultural partner,
we offer you quality and efficiency combined with
reliable servicing.
In order to assess the spare-parts demand for our
agricultural machines and to take these demands
into consideration when developing new machines,
we would ask you to provide us with some details.
Furthermore, we will also be able to inform you of new
developments.

Содержание MULTICAT 9000




































Отзывы: