PlayNation Play Systems 2500-1 Скачать руководство пользователя

Страница: 17 / 87

General Info to Review Before Installation

• Depending on your experience, assembly of the playset can take as little as 6 hours

up to 24 hours, depending on size, after inventory of parts; therefore, we recommend

you set aside a full two days for assembly.

• Identify all of the parts for your play set. Empty each box and lay out boards so you

can see each part. Your instruction book will have detailed drawings that will make it

easy for you to recognize individual parts. Keep all hardware and metal parts separate

from wooden pieces.

• After everything is laid out, check carefully to ensure all parts are present. Make sure

there are no broken boards.

• Find an area to sort your hardware. It is best to open the hardware on a solid surface

so that you do not lose any pieces in the grass. This will save time and familiarize you

with all the different pieces in the hardware bag.

• Important note: Wood has some natural defects such as knots, surface cracks, etc…

We reject parts that are structurally defective. We use a high quality lumber in our

structures; however, you should inspect each part for splinters or rough spots and sand

them smooth to prevent injury.

• After familiarizing yourself with all of the components, read all instructions thoroughly.

Reading instructions after you have studied the parts will help you understand the

installation process, and help to eliminate unnecessary mistakes.

• Pay close attention to the diameter and length of each bolt and screw.

• Never tighten hardware completely at first. It helps to have some adjustment for bolt

alignment while you are attaching parts together. After everything is square, tighten

each joint.

• After the main unit is assembled it is critical that the floor is level and square. If the

main frame is not level, the walls and floor will be out of square.

• After you complete installation, make sure every bolt, screw, and nut is tight, and every

board is secure. Wood will expand and contract with the seasons.

• Place the set on level ground, not less than 6 feet from any structure or obstruction

such as a fence, garage, house, overhanging branches, laundry lines, or electrical

wires.

Содержание 2500-1
























































































Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды

PlayNation Play Systems 2500-1, Руководство по сборке

Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды