PlayNation Play Systems 2500-1 Скачать руководство пользователя

Страница: 50 / 87

44 3

16 "

CENTER SUPPORT

ARCH ROCK WALL

THE INSIDE OF THIS BOARD**.

CENTER SUPPORT EXTEND BEYOND

SIDE SUPPORT

5/4 X 4 X 47-1/2"

ARCH ROCK WALL

OF THE ARCH ROCK WALL

2 X 6 X 50"

ROCK WALL BOARD

5/4 X 4 X 47-1/2"

#8 X 2"

WOOD SCREW

**DO NOT LET THE TOP TIP

NOTE:

THIS BOARD MAY NEED TO BE RELOCATED

IN THE NEXT STEP.

OFFSET THE TOP MIDDLE SCREW

HERE DOWN 1" FROM

THE HOLE.

STEP 12: ATTACHING THE ROCK WALL CENTER SUPPORT

TOP

1: BEGIN WITH THE 5/4 X 4 X 47-1/2" ROCK WALL BOARD AND SECURE IT TO THE ARCH ROCK WALL SIDE

SUPPORT WITH TWO #8 X 2" WOOD SCREWS PER SIDE. THE ROUNDED EDGE OF THE ROCK WALL BOARD

SHOULD BE AGAINST THE CORNER POSTS BEFORE ATTACHING.

2: NEXT THE 5/4 X 4 X 47-1/2" ROCK WALL BOARD WILL MOUNT AT THE BOTTOM. THIS BOARD WILL BE AT

44-3/16" FROM THE TOP ROCK WALL BOARD AND FLUSH TO THE ROCK WALL SIDE SUPPORTS. SECURE

WITH #8 X 2" WOOD SCREWS.

3: WHEN FASTENING THE ARCH ROCK WALL CENTER SUPPORT NEXT DO NOT LET THE TOP TIP EXTEND

BEYOND THE INSIDE OF THE TOP ROCK WALL BOARD. PLACE THE ARCH ROCK WALL CENTER SUPPORT

BEHIND THE ROCK WALL BOARDS AND CENTER IT UNDER THE SMALL HOLES. THE TOP 2" SCREW SHOULD

BE OFFSET DOWN 1" FROM THE CENTER OF THE TOP BOARD. FASTEN THE ARCH ROCK WALL CENTER

SUPPORT TO THE ROCK WALL BOARDS WITH #8 X 2" WOOD SCREWS.

BOTTOM

ARCH

ROCK

WALL

CENTER

SUPPORT

Содержание 2500-1
























































































Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды

PlayNation Play Systems 2500-1, Руководство по сборке

Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды