PlayNation Play Systems 2500-1 Скачать руководство пользователя

Страница: 44 / 87

STEP 6: ATTACHING ARCH FACE BOARD AND DECK SUPPORTS

1: THE 2 X 6 X 47-1/2" ARCH FACE BOARD (WITH FOUR PRE-DRILLED HOLES) ATTACHES TO THE SET OF HOLES BELOW

THE TOP MOST HOLES. ATTACH THE BOTTOM ARCH FACE BOARD HOLES USING 5/16" X 4" HEX BOLTS AND 5/16"

WASHERS. SQUARE THE ARCH FACE BOARD TO THE CORNER POSTS. PREDRILL 9/64" HOLES 2-1/2" DEEP THROUGH

THE TOP HOLES INTO THE CORNER POSTS. ATTACH THE TOP ARCH FACE BOARD HOLES USING 5/16" X 3-1/2" LAG

SCREWS AND 5/16" WASHERS.

2: THE 2 X 4 X 47-1/2" DECK SUPPORT BOARDS (WITH TWO PRE-DRILLED HOLES) ATTACH TO THE SET OF HOLES

ABOVE THE SANDBOX BOARD AND THE END SANDBOX BOARD ON THE INSIDE OF THE LEFT AND RIGHT SIDE OF THE

CORNER POSTS WITH 5/16" X 4" HEX BOLTS AND 5/16" WASHERS.

HOLES SHOULD BE OFFSET DOWN ON BOTH DECK SUPPORT BOARDS.

2 X 4 X 47-1/2"

ARCH FACE BOARD

5/16" X 4"

5/16"

HEX BOLT

LAG SCREW

DECK SUPPORT

FRONT OF PLAY SET

2 X 6 X 47-1/2"

5/16" X 3-1/2"

5/16" WASHER

WASHER

HEX BOLT

5/16" WASHER

5/16" X 4"

(OFFSET DOWN)

SQUARE POST

TO ARCH

BOARD

BEFORE

DRILLING FOR

LAGS.

Содержание 2500-1
























































































Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды

PlayNation Play Systems 2500-1, Руководство по сборке

Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды