PlayNation Play Systems 2500-1 Скачать руководство пользователя

Страница: 85 / 87

STEP 47: GROUND STAKES

1: HAMMER A GROUND STAKE INTO THE EARTH NEXT TO EACH SWING LEG AT AN ANGLE. DO NOT

HOLD THE UPPER PORTION OF THE STAKE AFTER THE FIRST COUPLE OF HITS OR IT MAY VIBRATE HARSHLY

AGAINST YOUR HAND. IF THE TOP PART OF THE STAKE TWISTS WHEN IT ENCOUNTERS A ROCK OR ROOT

YOU MAY HAVE TO BEND THE TOP PORTION OF THE STAKE AGAINST THE SWING LEG. FINALLY INSTALL

THE SCREW AND WASHER.

2: ATTACH EACH GROUND STAKE TO THE SWING LEG WITH A #14 X 2" PAN HEAD SCREW AND A 1/4"

FENDER WASHER PROVIDED WITH THE GROUND STAKE.

3: ON THE CORNER POSTS ON THE ROCK WALL SIDE OF THE FORT, DRIVE THE GROUND STAKES INTO THE

GROUND TO A DISTANCE THAT WILL NOT INTERFERE WITH THE T-NUTS OR HEX BOLTS THAT ARE

INSTALLED IN THE SANDBOX BOARDS. THE GROUND STAKES WILL BE ON THE INSIDE OF THE SANDBOX

ON THE CORNER POSTS.

4: ATTACH EACH GROUND STAKE TO THE CORNER POST WITH A #14 X 2" PAN HEAD SCREW AND A

1/4" FENDER WASHER PROVIDED WITH THE GROUND STAKE.

SWING LEGS

GROUND STAKE

DETAIL A

SWING LEG

#14 X 2" PAN HEAD

SCREW AND 1/4"

FENDER WASHER

INCLUDED WITH

GROUND STAKE

CORNER POSTS

GROUND STAKES

CORNER

DETAIL B

STAKE

POST

#14 X 2" PAN HEAD SCREW

AND 1/4" FENDER WASHER

INCLUDED WITH GROUND

GROUND STAKE

Содержание 2500-1
























































































Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды

PlayNation Play Systems 2500-1, Руководство по сборке

Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды