PlayNation Play Systems 2500-1 Скачать руководство пользователя

Страница: 51 / 87

STEP 13: ATTACHING THE ROCK WALL BOARDS

1: PLACE A 3/8" WASHER OR A QUARTER BETWEEN THE ROCK WALL BOARDS. MOUNT THE NEXT ROCK WALL

BOARD TO THE ROCK WALL SUPPORTS WITH #8 X 2" WOOD SCREWS.

2: REMOVE THE WASHERS OR QUARTERS AND PLACE THEM BETWEEN THE NEXT ROCK WALL BOARD AND

THE PREVIOUS ONE. MOUNT THE NEXT ROCK WALL BOARD TO THE ROCK WALL SUPPORTS WITH #8 X 2"

WOOD SCREWS.

3: REPEAT SUBSTEP 2 UNTIL YOU GET TO THE LAST BOARD. THE LAST BOARD MAY NEED TO BE ADJUSTED. IF

NECESSARY REMOVE THE LAST BOARD AND PLACE THE WASHERS OR QUARTERS BETWEEN IT AND THE PRIOR

BOARD. RESECURE THE LAST BOARD TO THE ROCK WALL SUPPORTS.

4: NOW PLACE THE BOTTOM ROCK WALL BOARD INTO POSITION SPACING IT AS BEFORE WITH WASHERS OR

QUARTERS. SECURE THE BOTTOM ROCK WALL BOARD TO THE ROCK WALL SUPPORTS WITH #8 X 2" WOOD

SCREWS.

5/4 X 4 X 47-1/2"

ROCK WALL BOARD - BOTTOM

WITH HOLE. BIG HOLE IS OFFSET UP.

NOTE THIS LAST BOARD

MAY NEED TO BE

REMOVED AND ADJUSTED

UP OR DOWN.

5/4 X 4 X 47-1/2"

ROCK WALL BOARD

#8 X 2" WOOD SCREWS

PLACE A QUARTER OR A 3/8" WASHER HERE TO SPACE THE ROCK WALL

BOARDS APART FROM ONE ANOTHER. THEN SECURE THE ROCK WALL

BOARD WITH #8 X 2" WOOD SCREWS. REMOVE THE WASHERS OR

QUARTERS. THEN REPLACE THE WASHERS OR QUARTERS BETWEEN THE

PRIOR BOARD AND THE NEXT BOARD AND REPEAT THIS PROCESS.

Содержание 2500-1
























































































Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды

PlayNation Play Systems 2500-1, Руководство по сборке

Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды