PlayNation Play Systems 2500-1 Скачать руководство пользователя

Страница: 47 / 87

2 X 4 X 47-1/2"

FORT SIDE SUPPORT

SQUARE END

SANDBOX

BOARD TO

CORNER

POSTS.

2 X 4 X 47-1/2"

FORT SIDE SUPPORT

DETAIL A

SCALE 1 : 8

T-NUT

(INSTALL FIRST)

5/16" WASHER

5/16" X 2-1/2"

HEX BOLT

SCALE 1 : 8

DETAIL B

2-1/2" WOOD SCREW

3" WOOD SCREW

STEP 9: ATTACHING FORT SIDE SUPPORTS

1: LAY THE 2 X 4 X 47-1/2" FORT SIDE SUPPORTS ON A FLAT SURFACE WITH THE ANGLED ENDS

ORIENTED THE WAY THEY WILL BE INSTALLED ONTO THE FORT. PLACE A T-NUT IN THE PRE-DRILLED

HOLE ON THE END AND SECURE WITH HAMMER.

2: THE 2 X 4 X 47-1/2" FORT SIDE SUPPORT (WITH ANGLED ENDS) ATTACHES TO THE HOLES ON THE

END OF THE END SANDBOX BOARD ON THE INSIDE WITH 5/16" X 2-1/2" HEX BOLTS AND 5/16"

WASHERS. THE ANGLED END SHOULD REST FLUSH AGAINST THE CORNER POST. SEE DETAIL A

AND DETAIL B.

3: ENSURE THAT THE TWO FORT SIDE SUPPORTS ARE ATTACHED PROPERLY TO THE END SANDBOX

BOARD BEFORE SECURING THEM TO THE CORNER POSTS. SQUARE THE 2 X 6 END SANDBOX

BOARD TO THE CORNER POSTS. USE A 2-1/2" WOOD SCREW IN THE TOP HOLE OF THE FORT SIDE

SUPPORT, THEN USE A 3" WOOD SCREW IN THE BOTTOM HOLE OF THE FORT SIDE SUPPORT. SEE

DETAIL B.

Содержание 2500-1
























































































Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды

PlayNation Play Systems 2500-1, Руководство по сборке

Результаты поиска

Содержание 2500-1

Отзывы:

Похожие инструкции для 2500-1

Бренды по названию

Популярные бренды