Pitney Bowes F767 Скачать руководство пользователя страница 31

Страница: 31 / 66

SDC927D

2-15

Operation • 2

Raise the F767 Top Cover and

lower the Front Cover.

Rotate knob

clockwise to set the

Accumulator Side Guides. The

correct setting allows approximately

3mm overall clearance so that

the material is controlled but not

restricted.

Setting the

Accumulator

Side Guides

Lower the Front Cover and turn

knob

anticlockwise to open the

Accumulator Side Guides. Close

the Front Cover.

Load a sheet or booklet.

Press

Run Confirm (Green)

until

a piece is fed into the accumulator

area.

Transport

Material to

Accumulator

Ramp

Adjustment

Ensure a piece of material is in

the accumulator area as in the

Accumulator Side Guide setting

above.

Squeeze the tabs

together and

slide the ramp until the yellow

indicators on the ramp align with

the material rear edge.

Close all covers.

Содержание F767



































































Результаты поиска

Содержание F767

Отзывы:

Бренды по названию

Популярные бренды

Pitney Bowes F767, Руководство оператора

Результаты поиска

Содержание F767

Отзывы:

Бренды по названию

Популярные бренды