17
Die Faxweiche
If you cannot receive any faxes, you may have set both
ringing signal numbers too high (see points 2 and 4). Set
both ringing signal numbers to values lower than five .
If you are using other devices apart from the fax machine
(telephones, answering machines), which are not connected by
serial links (see Glossary), the ringing pattern may change as
follows: Other devices ring as often as set under
FAX RINGS
.
Your fax will ring as often as set under
TAM RINGS
or
TOTAL RINGS
.
Special settings
Silent fax reception
FAX RINGS: 0
To receive faxes without any ring signals, set the amount of ring
signals in
FAX RINGS
to
0
.
Completely silent operation
You should use this option only
with devices with integral answer-
ing machines
. If, for example, you do not wish to be disturbed by calls
or faxes arriving at night, you may set the number of ringing signals to 0.
Faxes are then received silently and calls are immediately answered by the
answering machine, provided you have switched the answering machine
on.
For devices without integral answering machine
the fax-switch
is turned off, i.e. your device immediately switches over to fax reception
and will not ring, when calls are received (the caller hears a whistling
tone).
ATTENTION: For this reason calls cannot be recorded by any
external answering machine which may be connected.
Manual fax reception
fax: manual
If you select
fax: manua
, then faxes are only automati-
cally printed out by your fax machine, if you activate the fax
reception by pressing
START
. This may be sensible for example,
if you wish to receive your faxes by modem at your computer.
Economy operating mode - answering machine *)
TAM RINGS: 5/2
If you select option
5/2
at
TAM RINGS:
, then your answering
machine will start after two ringing signals instead of after five,
when you receive messages. Via the remote access function you
have the opportunity to check, whether your answering machine
holds any messages without incurring telephone costs (if your
answering machine turns itself on after only two ringing signals
you will know, that new messages have been left). After listening
to your new messages your answering machine will, at the next
call, switch itself on again after five ringing signals.
Mode
U
U
U
U
U
The default operating mode set in the factory is
S
. You may
also select operating mode
U
. In mode
U
your machine switches
automatically between
S
and
M
. The factory setting provides
that your machine switches at 10 pm to
M
and at 6 am back to
S
.
U
U
U
U
U
activating/deactivating
1
If you want to switch on function
U
, press
SM
for two seconds,
until you hear a confirmation tone and
U
appears on the display.
2
If you want to switch off function
U
, press
SM
for two
seconds, until you hear a confirmation tone and
U
disappears. On the display appears
S
or
M
.
U
U
U
U
U
configuring/checking
1
Select
function 33
by pressing
MENU
and numbers
3
and
3
. Press
OK
.
2
Enter the time at which you want your fax machine to
switch automatically to
S
and confirm with
OK
.
3
Enter the time at which you want your fax machine to
switch automatically to
M
. To confirm your settings press
OK
.
EASYLINK
Setting additional devices
The three codes below will help you, when you receive a call on an
additional telephone and wish to transfer a call or fax to your fax ma-
chine.
1
Code for starting your fax machine from another telephone:
*5
2
Serial connection
(see Glossary): Code for transferring a call
from another telephone connected serial to your fax machine:
*0
Please note that when using this code you have to replace
the handset of your additional device after you have
entered the code. See chapter
Telephone
/ Call transfer.
3
Parallel connection
(see Glossary): Code for turning off the
answering message, if the answering machine is switched
on:
**
For fax machines without built-in answering
machine
this code is used to switch off the fax machine.
*) only with built-in answering machine
