Philips AVENT Avent SCF260/34, Руководство пользователя

Страница: 4 / 31

WARNING!
The Digital Bottle and Baby Food Warmer is fitted with a non-rewirable moulded plug. The mains supply lead of the appliance
CANNOT be replaced. If the lead is damaged, the appliance should be discarded. The supplied lead must not be used
on any other appliance and no other cord should be used with the Digital Bottle and Baby Food Warmer.
This product is manufactured to comply with the Radio Interference Requirements and the EEC Directive 89/336/EEC.
Failure to follow instructions may cause scalding or damage to product.
• Always ensure water has been added before switching on the warmer.
• Always ensure that you are using the correct volume of water before beginning the warming cycle. The warmer should be
emptied of residual water before each subsequent use.
• Heating food jars or tins from frozen within this warmer is NOT RECOMMENDED.
• To avoid possible scalding, do not place hands over the lid flap or open the lid flap during the warming cycle.
• When warming a 330ml/11oz bottle, the lid flap will lift to accommodate the larger size. This will cause a small amount of
steam to rise from the warmer.
• To avoid possible scalding, take care when opening the lid after a completed cycle as there may be some residual steam.
• When in use, the warmer contains hot water. Be careful to avoid spilling any water on yourself when removing
contents from the warmer.
• Use the lifter to remove small bottles, VIA Cups, and small baby food jars or tins.
• Always use a cloth when removing bottles, cups, jars and tins from the warmer.
• Always check feed temperature before feeding.
• For microbiological and hygienic reasons, once heated, milk and food should not be reheated again.
• Never immerse the warmer or power cord in water.
• This appliance is intended for use by responsible persons, keep out of the reach of small children and the infirm.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure they do not play with the appliance.
• Failure to follow de-scaling instructions may cause irreparable damage.
• There are no serviceable parts inside the Digital Warmer. Do not attempt to open, service or repair the warmer yourself.
Philips AVENT guarantees that should the Digital Bottle and Baby Food Warmer become faulty during twelve
months from the date of purchase, it will be replaced free of charge during this time. Please return it to the
retailer where it was purchased. Please keep your receipt as proof of purchase, together with a note of when
and where purchased. For the guarantee to be valid, please note:
• The Digital Bottle and Baby Food Warmer must be used according to the instructions in this leaflet and
connected to a suitable electricity supply.
• The claim must not be a result of accident, misuse, dirt, neglect or fair wear and tear.
This guarantee does not affect your statutory rights.
Troubleshooting Guide
Food is not
warm enough
The temperature of warmed food depends on the consistency of the food. Philips AVENT recommends
that, ideally, pureed food only should be heated with this warmer. If you find that thicker food is not
warm enough at the end of the warming cycle, fill the warmer with an additional 30ml/1oz of water.
On step 4 and 5, choose the food from room temperature mode and programme the warmer at the
30ml/1oz option. Before feeding your baby, stir the food. Always check food temperature before feeding.
Milk is not
warm enough
If you find that milk is not warm enough at the end of a warming cycle, fill the warmer with an additional
30ml/1oz of water. On step 4 and 5, choose the milk from room temperature mode and programme the
warmer at the 30ml/1oz option. Before feeding your baby, shake the bottle or storage container gently
and check the temperature of the milk by sprinkling a few drops on the back of your hand.
Display will
not illuminate
/ Warmer will
not turn on
Check that the lid is closed correctly. Check that the mains lead is plugged into the mains and the power
outlet is switched on. Then hold the Power/Mode Selection Button for 3 seconds.
Symbols on
the display
are flashing
• If the milk, room temperature and ml/oz symbols are flashing, then the lid has not been closed correctly.
• If all volume symbols are flashing, and the warmer beeps intermittently for 30 seconds then the cycle is
complete. Follow Step 8 onwards to remove the bottle or container from the warmer.
• If all mode and starting temperature symbols are flashing, then the unit requires de-scaling. See section
‘Care of your Digital Bottle and Baby Food Warmer’ on page 6. To acknowledge the de-scale warning,
press and hold the Power/Mode Selection or Volume Selection/Start Button for 3 seconds. If you do not
wish to de-scale, please be aware that this may cause irreparable damage.
The warmer
is beeping
• If ml/oz symbols flash, and the warmer beeps twice, insufficient water has been placed in the warmer.
Unplug the warmer, discard the milk or food and empty any remaining water. Be careful as the warmer is
hot. Follow instructions from Step 1 onwards.
• If all volume symbols are flashing, and the warmer beeps intermittently for 30 seconds then the cycle is
complete. Follow Step 8 onwards to remove the bottle or container from the warmer.
To stop the
warming cycle
Press the Power/Mode Selection Button and the warmer will beep and return to default settings.
To start the
warming cycle
Once the correct mode, starting temperature and volume have been selected, press and hold the Volume
Selection/Start Button until the warmer beeps.
If the lid is
opened during
warming cycle
If the lid is opened at any time during the warming cycle, the lights on the display panel will flash and
the warmer will stop and return to default settings. In order to reset the warmer after the lid has been
opened, empty out any residual water, then follow instructions for use from step 1 onwards. Since this
could occur at any stage of the warming cycle, milk or food should be discarded for safety reasons.
Difficulty
setting the
appropriate
amount of
frozen food
The maximum volume that may be selected when warming food from frozen is 230ml/8oz.
Care of your Digital Bottle and Baby Food Warmer
Always unplug the warmer and allow it to cool before cleaning. Wipe the inside and outside of
the warmer with a damp cloth. DO NOT USE AN ABRASIVE CLEANER. Using cool pre-boiled or
filtered water in your warmer may reduce limescale build-up. When the warmer needs de-scaling,
the mode and starting temperature symbols will flash on the electronic display. To ensure maximum
effectiveness, you should de-scale your warmer every time it is required. To acknowledge the de-scale
warning, press and hold the Power/Mode Selection or Volume Selection/Start Button for 3 seconds.
If you do not wish to de-scale, please be aware that the unit will not remind you to de-scale on your
next use, but will instead begin re-counting cycles until the next de-scaling is needed.
IMPORTANT! DE-SCALING
Under no circumstances should anything other than citric acid or vinegar be used as it may cause
irreparable damage. Avoid contact with eyes as this may cause irritation. Keep out of the reach of children.
EITHER:
Mix one sachet of citric acid* (10g) with 200ml/7oz of water. Pour solution into the empty warmer.
DO NOT place a bottle, jar or cup into the warmer when de-scaling. Close the lid of the warmer
and programme the warmer to run with 310ml/11oz of milk from frozen. After the warming cycle
has ended, leave the solution to cool for 30 minutes before emptying the warmer and rinsing with tap
water. Wipe the inside and outside of the warmer with a damp cloth only.
OR:
Pour 100ml/3.5oz of vinegar mixed with 200ml/7oz of cold water into the warmer. Allow liquid to
stand in the unit until any limescale has dissolved. DO NOT place a bottle, jar or cup into the warmer
when de-scaling. DO NOT start the warming cycle. Empty the unit and rinse thoroughly. Wipe the
inside and outside of the warmer with a damp cloth only.
*Citric acid is available from most chemists and through Philips AVENT Customer Service.
Guarantee