Perkins 402D Скачать руководство пользователя страница 85

Страница: 85 / 98

This document is printed from SPI². Not for RESALE

SEBU8311-02

Maintenance Section

Fuel System Primary Filter/Water Separator - Drain

g01306131

Illustration 59
Typical example

By using a suitable tool, remove spin-on

lter (1).

Ensure that any

uid is drained into a suitable

container.

Note:

Do not

ll the fuel

lter with fuel. The fuel will

not be

ltered and the fuel could be contaminated.

Contaminated fuel can damage your fuel system.

Install the new spin-on

lter. Tighten the spin-on

lter by hand.

The fuel system will need to be primed after the

new

lter is installed. Refer to this Operation and

Maintenance Manual, “Fuel System - Prime”.

i02627223

Fuel System Primary

Filter/Water Separator - Drain

Fuel leaked or spilled onto hot surfaces or elec-

trical components can cause a

re. To help pre-

vent possible injury, turn the start switch off when

changing fuel

lters or water separator elements.

Clean up fuel spills immediately.

NOTICE

The water separator is not a

lter. The water separa-

tor separates water from the fuel. The engine should

never be allowed to run with the water separator more

than half full. Engine damage may result.

g01316965

Illustration 60
Typical example

Open drain (1). Catch the draining

uid in a

suitable container. Dispose of the drained

uid

correctly.

Close drain (1).

NOTICE

The water separator is under suction during normal

engine operation. Ensure that the drain valve is tight-

ened securely to help prevent air from entering the fuel

system.

Содержание 402D


































































































Результаты поиска

Содержание 402D

Отзывы:

Perkins 402D, Руководство по эксплуатации и обслуживанию, Страница: 85 / 98

Результаты поиска

Содержание 402D

Отзывы: