Perkins 402D Скачать руководство пользователя страница 59

Страница: 59 / 98

This document is printed from SPI². Not for RESALE

SEBU8311-02

Maintenance Section

Maintenance Recommendations

Stop the engine. Turn the switched power to the

OFF position.

Disconnect the negative battery cable from the

battery. If a battery disconnect switch is provided,

open the switch.

Disconnect the J1/P1 and J2/P2 connectors from

the ECM. Move the harness to a position that will

not allow the harness to accidentally move back

and make contact with any of the ECM pins.

g01143634

Illustration 31

Connect the welding ground cable directly to the

part that will be welded. Place the ground cable as

close as possible to the weld in order to reduce the

possibility of welding current damage to bearings,

hydraulic components, electrical components, and

ground straps.

Note:

If electrical/electronic components are used

as a ground for the welder, or electrical/electronic

components are located between the welder ground

and the weld, current

ow from the welder could

severely damage the component.

Protect the wiring harness from welding debris

and spatter.

Use standard welding practices to weld the

materials.

Содержание 402D


































































































Результаты поиска

Содержание 402D

Отзывы:

Perkins 402D, Руководство по эксплуатации и обслуживанию, Страница: 59 / 98

Результаты поиска

Содержание 402D

Отзывы: