Perkins 402D Скачать руководство пользователя страница 27

Страница: 27 / 98

This document is printed from SPI². Not for RESALE

SEBU8311-02

Operation Section

Lifting and Storage

Exhaust System

•

Remove the exhaust pipe. Spray

1762811

POWERPART Lay-Up 2 into the turbocharger. The

duration of the spray is printed on the container.

Seal the turbocharger with waterproof tape.

General Items

•

If the lubricating oil

ller is installed on the valve

mechanism cover, remove the

ller cap. If the

lubricating oil

ller cap is not installed on the valve

mechanism cover, remove the valve mechanism

cover. Spray

1762811

POWERPART Lay-Up 2

around the rocker shaft assembly. Replace the

ller cap or the valve mechanism cover.

•

Seal the vent of the fuel tank or the fuel

ller cap

with waterproof tape.

•

Remove the alternator drive belts and put the drive

belts into storage.

•

In order to prevent corrosion, spray the engine with

1734115

POWERPART Lay-Up 3. Do not spray

the area inside the alternator.

When the engine protection has been completed in

accordance with these instructions, this ensures that

no corrosion will occur. Perkins are not responsible

for damage which may occur when an engine is in

storage after a period in service.

Your Perkins dealer or your Perkins distributor can

assist in preparing the engine for extended storage

periods.

Содержание 402D


































































































Результаты поиска

Содержание 402D

Отзывы:

Perkins 402D, Руководство по эксплуатации и обслуживанию, Страница: 27 / 98

Результаты поиска

Содержание 402D

Отзывы: