Perkins 402D Скачать руководство пользователя страница 16

Страница: 16 / 98

This document is printed from SPI². Not for RESALE

SEBU8311-02

Product Information Section

Model Views

g01305224

Illustration 12

Front and left side view of the 404D-22T Engine
(13) Top engine oil

ller cap

(14) Crankcase breather
(15) Rear Lifting eye
(16) Air inlet elbow
(17) Valve mechanism cover
(18) Turbocharger

(19) Water temperature regulator housing
(20) Starting motor solenoid
(21) Electric starting motor
(22) Alternator
(23) Engine oil pan
(24) Engine oil drain plug

(25) Fan drive belt
(26) Crankshaft pulley
(27) Coolant temperature switch
(28) Cooling fan

i02959055

Engine Description

The 400 series engines are indirect injection engines.

The engines are controlled with a mechanically

actuated fuel injection pump. The engine cylinders

are arranged in-line.

The cylinder head assembly has one inlet valve and

one exhaust valve for each cylinder. Each cylinder

valve has a single valve spring.

The pistons have two compression rings and an

oil control ring. It is important to ensure the correct

piston height so that the piston does not contact the

cylinder head. The correct piston height also ensures

cient combustion of fuel that is necessary in order

to conform to requirements for emissions.

The crankshaft for a two cylinder engine has two

main bearing journals. The crankshaft for a three

cylinder engine has four main bearing journals. The

crankshaft for a four cylinder engine has

ve main

bearing journals. End play is controlled by the thrust

washers that are located on the rear main bearing.

Содержание 402D


































































































Результаты поиска

Содержание 402D

Отзывы:

Perkins 402D, Руководство по эксплуатации и обслуживанию, Страница: 16 / 98

Результаты поиска

Содержание 402D

Отзывы: